Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Homemade slot mortiser w/ PICS *LINK*

Posts

Homemade slot mortiser w/ PICS *LINK*

#1

Homemade slot mortiser w/ PICS *LINK*

Paul Cates - Henderson, KY

>Hi everyone,

This is my first attempt at posting pictures�hope it works!

When I owned a Rojek mortiser, it was my favorite power tool, so after I sold it I decided to try to build something similar but cheaper. For the up/down adjustment, I found the following hunk of iron at a local surplus dealer for $100. It was greasy and a bit rusty, so I spent some time cleaning, sanding and repainting.


I used the 40 (mm) series 8020 linear bearings because at the time of purchase, 8020�s surplus site on eBay had both the rails and bearings in stock. The 40 series is plenty beefy, so I think the smaller sizes would work fine. The head of a 5/16� carriage bolt fits nicely into the rail slots to secure the rails to the cast table. 8020 also sells shims to make the bearings fit snugly to the rails. These are not mandatory if the bolt holes in the table are large enough to allow you to adjust the bearings to ride against the rails, but the shims are an easy way to remove slop while moving the X-Y table (vs. endless adjustments without them). DAMHIKT!


I investigated using an induction motor with a chuck attached to either the motor shaft or a mandrel, but it seemed more trouble/expense that it was worth, thus I went the router route. I made the box holding the Bosch 1617 EVS router out of plywood, with a detachable top/back. I bought the variable speed router thinking I could use it at less than full speed to cut down on the noise. It works fine, but if I had to do it over, I�d probably use a more powerful router. I can imagine a piece of red oak stopping the Bosch with a �� bit on low speed. Rick L. gave me lots of pointers and advice via email, and I copied some of the features of Dan Barber�s Mortise-Flex (see the articles section here on WC).


The port for dust collection is on the back:


Side to side adjustments and hold downs:


To make the lever, I bought some rod ends on eBay but couldn�t find a solid steel rod to fit through the rod end without a lot of slop. �� was too big, so I used a 3/8� threaded rod on the inside of a hollow aluminum tube. There is a little flex in the lever, but it works fine.


I posted a video of the mortiser in action at the link below. It�s an 11mb file. The speed is set on 4 (out of 6) and I�m cutting a mortise in cherry with a two flute 3/8� end mill.


Mortiser on YouTube

Re: Homemade slot mortiser w/ PICS *LINK*

#2

Paul Kramer

Paul -- Very Cool Tool!

Paul Kramer

>

Re: Homemade slot mortiser w/ PICS *LINK*

#3

Re: Homemade slot mortiser w/ PICS

Robert R Clough - Thorncraft

>Seems to me, Paul, your machine is basically a horizontal roouter table. Yours is heavier built than the table I made about 10 yrs ago now, but it appears to do the same job. Mine has the height adjustment for the router, and an x and y table.

I don't use it very often, but when I do, it does the job.

Re: Homemade slot mortiser w/ PICS *LINK*

#4

Awesome!

Mark Goodall - ATL - tooljunkie

>

Re: Homemade slot mortiser w/ PICS *LINK*

#5

Nice setup Paul

Jim Dillon

>I don't have a horizontal mortiser (yet 8-)) but have always been fascinated by their construction and what they can do. Thanks for taking the time to show us yours; and your pics downloaded just fine even on my dial-up.

Jim

Re: Homemade slot mortiser w/ PICS *LINK*

#6

Re: Homemade slot mortiser w/ PICS

Jesse in New Mexico

>Way cool. That is one sweet tool!!

One question, at school they taught us to use the slot mortiser by taking shallow cuts along the width of the mortise, and then going deeper until done. I see you bore all the way down, then move along the width, and finish with a sweep along the width. Is that just the way you like to do it or do you use that technique to ease the strain on the router?

Thanks for sharing! Awesome machine!

Re: Homemade slot mortiser w/ PICS *LINK*

#7

Nice job, Paul. Great dust collection.

Eddie Pacheco, San Jose, Ca.

>On the video it looks like there is very little dust that gets away fron the works surface area.

Re: Homemade slot mortiser w/ PICS *LINK*

#8

Re: Homemade slot mortiser w/ PICS

Paul Cates - Henderson, KY

>Yes, I'm especially concerned about the strain on the bit. I may try your method though, since the steel end mills should handle side stress.

Re: Homemade slot mortiser w/ PICS *LINK*

#9

BRAVO!

Dan Barber

>Paul,

Excellent job, I particularly like the reuse of found equipment. The 80/20 slides should work well. I prefer multiple shallow passes for the greatest accuracy. Great Job!

Dan

Re: Homemade slot mortiser w/ PICS *LINK*

#10

Well done Paul

HC Sakman

>"8020 linear bearings because at the time of purchase, 8020�s surplus site on eBay"

That's exactly what I've been looking for, those linear bearings. Where's the source? Who makes them?

Chunk of iron is also impressive to begin with. Excellent job overall.

Chico...

Re: Homemade slot mortiser w/ PICS *LINK*

#11

Re: Well done Paul

Paul Cates - Henderson, KY

>Thanks Chico.

8020's main site is here:

http://www.8020.net/

The eBay "garage sale" site is here:

http://stores.ebay.com/8020-Inc-Garage-Sale

I can post more info later if you have any questions.

Re: Homemade slot mortiser w/ PICS *LINK*

#12

Rick L

Re: Thoughts...

Rick L

>Thanks for the mention!

I definitely would recommend you try the nibbbling method of taking 1/8" or 1/4" deep passes as you go back and forth. We've found it to be more accurate and easier on the bits and a neater mortise.

I much prefer the lower speeds of an induction motor over a router. A little bit slower than a router but it gives more options of horizontal boring with larger bits and even doweling.

Nice to see someone who realizes you don't need expensive linear ball bearings for the application. I've used quite a bit of the 80/20 stuff over the years. A much cheaper option is steel shafing and bronze bushings. Much cheaper by far and very simple. Very much over looked option for sliding fixtures for router tables, shapers and where ever one can be creative. See the Jessem coping fixture for the router table.

Consider destaco tyoe clamps on a horizontal bar on vertical posts. Your present set can be improved greatly.

Re: Homemade slot mortiser w/ PICS *LINK*

#13

Re: Homemade slot mortiser w/ PICS

Paul Cates - Henderson, KY

>I appreciate everyone's comments. I plan to put it to work this week making a sleigh bed and a chest of drawers. But at the pace I work, don't hold your breath too long for project pics. :)

Re: Homemade slot mortiser w/ PICS *LINK*

#14

Rick L

Re: Costs of 80/20

Rick L

>Curious as to what you spent on the 80/20 stuff.

Cost breakdown of the bearings, extrusions.

I've bought plenty of the stuff new. Just trying to see if I can get the cost of your machine down even further. I'm sure the bronze bushings and steel rod can be a big cost cutter.

Off the top of my head the shafts and bronze bushings for the machine would be around $64 plus dhipping from mcmaster. That would be 3/4" x 72" of shaft material and 12 3/4" bronze flanged bearings.

Ball joint rod ends would be around $36 for 2 pcs for 3/4" rod. I'm sure i could shave a bit more off.

I would definitely go with an induction motor and step pulley to have multiple speeds for doweling or mortising.

Shaft material threaded on one end is available off the shelf to fit a Jacobs chuck.

Re: Homemade slot mortiser w/ PICS *LINK*

#15

Re: Costs of 80/20

Paul Cates - Henderson, KY

>The bearings were $90, 8' of rail was $27, and I have a few feet left over. I bought too many shims ($5), but I didn't know exactly what I needed at the time. Total: $135 including shipping. $15 to a local machine shop to cut the bearings in half and also the rails. Rod ends - $20. Add a few odds/ends and the total is $180 or so.

When I was considering bronze bushings and steel shafts, I must have been looking at the wrong shafts because I remembered them being as much or more than the 80/20 stuff. What would you use for the shafts: type of steel/hardened/finish/tolerance?

Re: Homemade slot mortiser w/ PICS *LINK*

#16

Rick L

Re:Shaft material

Rick L

>Look up 1346K36 in mcmaster for a simple shaft material. A lot of simple applications from router table lifts to coping fixtures for routers and shapers.

http://jessem.com/mite_r_slide.htm

See the example of one application. The round rods have extra flexibility for applications that allow you to swing things out of the way.