Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Kickback followup

Posts

Kickback followup

#1

Kickback followup

Mark in B'ham

>As a follow up to my previous thread Kickback - Ouch I have put together a list of Rules of Thumb (to keep your thumbs on your hand) when setting up cuts on the tablesaw. I thought I would post them here for any corrections, annotations, and additions.

- Keep the workpiece as big as you can as long as you can. This usually means rip a board to width first then crosscut to length.

- Don�t try to use the fence for pieces that are too short. The piece should pass the blade reach the splitter once it is cut. As Lee Schierer said �The safety rule here is the length of the piece along the fence should always be 1-1/2 to 2 times the width between the fence and the blade.�

- Use the miter gauge or a crosscut sled for crosscut operations. A block can be clamped to the fence to use to keep things the same length, but the block should end before the blade to keep pieces from being trapped between the blade and the fence.

- Using feather boards with small pieces can be dangerous as well. As Jim Dillon notes, the piece may try to rotate when it disengages the feather board and contact the blade. Don�t place a feather board where it will push a piece directly toward to blade (i.e. right beside the blade).

- Stop and consider if the table saw is the best way to get the cut done. Smaller pieces can be more safely handled on the bandsaw. A handsaw and a miterbox might be the best solution if there are only a few cuts.

- Most important of all is to think through the cut before turning on the saw.

I hope these are helpful.

Mark

Just trying to keep all my fingers

Re: Kickback followup

#2

Re: Kickback followup

Alan Tolchinsky

>Mark, These are all great suggestions especially the last one. I think we all may be guilty of using the table saw when something else might be safer and easier to do the job. I'm guessing that the nice straight clean cuts off the table saw urge us to use it even when it's not suitable.

Re: Kickback followup

#3

Re: Kickback followup

John Lucas

>mark I had always used a 3/4" board on my fence as a stop when crosscutting small pieces. This supposedly prevents them from being trapped between the fence and blade. Wrong. I was cutting 3" square pieces and one rotated from vibration and air. The corners caught the blade and hit me in the chest hard enough to leave a bad bruise. I thought I had brocken a rib. now I have a 6" spacer that I use. It's easy to add 6" to any dimension so you can still use the tape on your table saw. Now there is 6" + the wood to keep from getting a kickback.

Re: Kickback followup

#4

Re: Kickback followup

Jim Dillon

>Mark,

That is a nice list of things to watch out for. When I first bought my table saw, I also picked up a copy of Kelly Mehler's book (1st edition) on using a TS. It was, and still is a godsend - at least for me. I still consult it from time-to-time to refresh my memory on how to do something safely. He has a 2nd edition out that is probably just as good. My one close call with kickback (knock-on-wood) was getting in a hurry and cross cutting a narrow piece like you were doing. Now, whenever I crosscut a piece narrower than 6 inches or so, I look for a safer way to do it. Thanks for getting back to us.

Jim

Re: Kickback followup

#5

I can add a few nevers.

Keith Newton

>Never leave a piece between the fence and blade, and then reach down to turn the saw off. Most saws will have enough wobble at some point of stopping, that they will grab a unattended piece in the slot, and send it flying.

Never rip narrow rippings without checking the piece from end to end. Checks or ring-shake that might end up making a separate piece, especially near the end of the cut can wedge itself under, and between the fence and blade, forcing the other part over onto the back of the blade, turning it into a spear.

Never allow anyone to stand in the down-range zone when you or anyone else is ripping.

If you are using a dado set low, that is only part of the thickness. Never feed with a backward walking motion where your hands pass directly over the blades. I have two professional woodworking friends who got mangled with this one.

Know your tool. If the trailing end of your fence can be flexed away from the blade with X amount of pressure, you or someone else can saw along pushing the work too hard into the fence flexing it aside until the front of the blade exits the cut, then when you let up on that pressure, the fence can spring back over sending the work onto the back of the blade. Reminder, Always push the work clear of the back of the blade.

Always try to use a catch table. Inexperienced people pulling the stock out the back of the saw can really get things bound up in more ways than I can numerate.

Never reach over the back of the saw and grasp the work by pinching the work together on the blade as it exits the cut. I worked with an old carpenter about 25 years ago that did that for over twenty years, but he lost his fingers before he retired.

Re: Kickback followup

#6

Re: Kickback followup

Larry Marker in Alabama

>I think one of the greatest inventions for table saw safety is the Grrr-Ripper (or however they spell that.) With that tool, I feel quite safe running a piece through the blade that is too small to cut on the table saw safely by any other method. They give you complete control of the piece between the blade and the fence and also the off-cut on the free side of the blade.

I have two of them and wouldn't part with them.

I have no affiliation with this product other than being a happy owner.

Larry

Re: Kickback followup

#7

Re: Kickback followup

Mark inb'ham

>Thanks everyone for your great comments.

I thought of two more to add.

- Always make sure that you have enough room for the cut on the out feed side of the table. This has happened to me in my old smaller shop. I got almost through a cut and then the board hit something and I had to stop the saw. No injury and I finished the cut with a handsaw.

- Allow for flexing of the boards. It has also happened that I set up my workmate table to support the outfeed but the board flexed before it reached the table and went under it. Remember that the once they are cut, the thinner pieces will flex more than the solid board you started with.

Re: Kickback followup

#8

Been there!

Tony - Memphis

>My shop is small too. Fortunately, no issues other than a good laugh at myself and a learned habit to make sure there is room.

Tony