Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

OT: Well pump

Posts

OT: Well pump

#1

OT: Well pump

Joey, Ct.

>My well pump is turning on and off too frequently. They came two years ago to service it. My neighbor and friend, said he serviced his own. Unfortunately he died, taking the secret with him. Something about draining the air pressure or restoring it? I have a regulator dial with what looks like an air inlet. Anyone have the knowledge? Thanks Joe

Re: OT: Well pump

#2

Re: Charging a pressure tank (water well).

Al Stokka - Cambridge, Iowa

>Turn off the pump or close the water-inlet valve to the pressure tank. Drain most of the water from the pressure tank (needn't be entirely empty). Charge the pressure tank with about 35 PSI of air (the exact PSI isn't critical). Open the water-inlet valve or turn the pump back on.

Pat yourself on the back, have a cold one, and tell the sife how smart you are and how much money you saved.

Al

Re: OT: Well pump

#3

Re: One more thing

Al Stokka - Cambridge, Iowa

>Before draining the water from the pressure tank, you'll want to close the water-outlet valve as well as the inlet valve. Otherwise, you end up draining most of the plumbing system. Doing so wouldn't hurt anything, but serves no useful purpose.

Al

Re: OT: Well pump

#4

Re: Thanks Al, You da Man!

Joey, Ct.

>

Re: OT: Well pump

#5

Re: Happy I could help.

Al Stokka - Cambridge, Iowa

>

Re: OT: Well pump

#6

Re: OT: Well pump

Bob Fawcett

>replace the valve that keeps air in the tank. Can't remember the proper name. costs should be less than $30. It usually screws in the side of the tank about halfway up.

Re: OT: Well pump

#7

Re: OT: Well pump

del schisler

>On a 42 gal. bladder tank the preasure should be set this way Find out what preasure switch you have Take the cover off of the switch and look in the cover It will say in the right hand side of the schematic A switch 40-60 should be air preasure set it at 38lbs A switch 30-50 should be 28lbs and 20-30 should be 18lbs It will work best set this way Mfd. setting's If the pump comes on when you turn on the faucet and when you shut the water off the pump stop's then turn the faucet on and the pump start's again like repeat the on and off the pump start's the bladder is bad Also you can let air of of the valve If water come's out it is bad

Re: OT: Well pump

#8

Re: OT: Well pump

Michael Stadulis, in Gloucester County, NJ

>Joey,

In case your problem isn't recent, most time the hydropneumatic tank for well water systems is too small and it causes short cycling that wears the pump out sooner. Why is the tank undersized.....because the plumber/well driller got you a system as inexpensively as he could, and nobody typically understands the cycling thing until they experience it. Short cycling is especially evident with a bigger family or just one or two girls.. ;o) or if you irrigate. Consider a bigger tank.

Mike

Re: OT: Well pump

#9

Re: OT: Well pump Long explanation

Larry Clinton At Frankfort (Central)., Indiana

>If you have a "Bladder" tank used as a reservoir / pressure tank, you should understand how it works - makes it easy to service if you know exactly what is happening. The Bladder in the tank is somewhat like a hot water bottle. The water is pumped into the bladder, expanding it until it almost fills the tank. When set up properly, the "tank" outside the bladder is pressurized at or just below the lower set point of your pressure switch on the pump (the point where the pump turns on, per the information Del posted. When the pump is off, (reached pressure) and you open a faucet, the pressure in the reservoir tank forces the bladder to become smaller, forcing the water out. You can use almost as much water as the reservoir holds as the pressure will remain above the low set point of the switch that turns your pump on. These usually don't require service (adding air pressure for several years. Your tank must have a small -pinhole- leak in the bladder. Replacement is very simple as there is usually only one pipe fitting into the tank. You can replace it with any size bladder or diaphragm tank. The larger the tank the longer you can run water between pump starts. You can also add additional tanks anywhere in the cold water system by adding a Tee and plumbing in the additional tank. Be sure the replacement or additional tank has the pressure set as above. The old tanks - without a diaphragm or bladder used a float and allowed air to be injected into the tank. When the "float" in the tank reached a high level, it allowed air to be sucked into the jet (or piston) pump through a small (usually 1/4 or 3/16") line from the tank to the pump head. These did not allow as much water to be used before the pump restarted for the same size tank. A much smaller diaphragm / bladder tank serves the same function.

Re: OT: Well pump

#10

Re: Schrader valve

Al Stokka - Cambridge, Iowa

>