Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

OT----Plastic piping to steel fitting?

Posts

OT----Plastic piping to steel fitting?

#1

OT----Plastic piping to steel fitting?

Gary Evans Tallassee, TN

>Hi all,

Apologies to those who object to off topic posts.

Two heating seasons ago I installed a wood furnace with an integral water coil. I plumbed the coil to a pre-heating tank with 3/4" cpvc. The pre-heating tank is a small water heater tank. The source and outlet water are plumbed with pvc and cpvc, respectively. I have had problems with the plastic to steel joints leaking. Recently, I overcoated those joints with fiber-reinforced bondo. It worked well for some of the joints, some still leak with changing temperatures.

I'd really be interested to know how to make these joints waterproof over a temperature range of 40 to 120 degrees.

Thanks much,

Gary

Re: OT----Plastic piping to steel fitting?

#2

Re: OT----Plastic piping to steel fitting?

Bill Turpin in WNC mountains

>Gary, I would use QUALITY teflon tape, not the cheap $.90/roll from Lowes or HD. Over-lap the layers. I would install a pressure relief valve as close to the wood heater coil as possible, with NO valves between the furnace and the PRV. Pipe the discharge of the PRV to the outside where it can drip without harm. Do not have threads on the end of this pipe, so that it can not be capped. The constant expansion/contraction of the water could be causing the leak. The valve will open/close and relieve the excess pressure. If there is not a PRV you have a BOMB! Locktite also makes a teflon based pipe dope that is vey good.

Bill in WNC mountains

Re: OT----Plastic piping to steel fitting?

#3

Re: OT----Plastic piping to steel fitting?

Keith Newton

>I will only use plastic on the male side of a pipe thread into a female metal.

Re: OT----Plastic piping to steel fitting?

#4

Re: OT----Plastic piping to steel fitting?

Gary Evans Tallassee, TN

>Hi Bill,

Long time, no see.

Admittedly, I had used the cheap teflon tape. Didn't know there was a choice. I do have a PRV on the tank, just like a normal water heater. No problems with overheating the system, just can't seem to get the joints to stay sealed. Like I said, there is a huge temp range to deal with and the two plastics and the steel all have different expansion/contraction rates.

The telfon liquid might be the way to go. Bear in mind that these joints did well through the last heating season. The leakage tends to occur when I let the system cool down.

I may just have to break down and buy steel pipe.

Thanks,

Gary

Re: OT----Plastic piping to steel fitting?

#5

Re: OT----Plastic piping to steel fitting?

Gary Evans Tallassee, TN

>Hi Keith,

That is exactly what I have. And I know that the differences in expansion and contraction are creating the leaks. I guess I will try the liquid teflon. If that doesn't work, it may be time for steel pipe.

Thanks,

Gary

Re: OT----Plastic piping to steel fitting?

#6

Re: OT----Plastic piping to steel fitting?

Barry Irby

>I would be leery of PVC piping, It is only rated for cold water. CPVC is rated for hot or cold water. Use the Teflon tape and make the plastic the male threads and the metal the female.

Most plastic pipe manufacturers and water heater makers recommend that you have at least 18" of metal pipe between the tank and the plastic pipe.

You might try Dresler couplings. They may work better over the extreme temperature range.

Re: OT----Plastic piping to steel fitting?

#7

Re: I thought PVC wasn't rated for hot water.

Al Crandall (N.E. of Indy)

>You mentioned using both pvc and cpvc. Are the leak in the pvc joints? It might be that pvc has a larger coefficient of expansion than cpvc and that is why it is leaking. I'm no plumber, but I am pretty sure one of those materials isn't rated for hot water, only cold. Must be a reason for it.

Re: OT----Plastic piping to steel fitting?

#8

Teflon tape versus liquid pipe dope...

Tim Greif - West of Chicago

>My dad was in the heating business and carwash business where he did alot of plumbing. He taught me early on that teflon tape is a very good thread lubricant, but not a reliable sealant. If you want leak free joints, use the liquid paste pipe dope.

Re: OT----Plastic piping to steel fitting?

#9

Re: OT----Plastic piping to steel fitting?

Bill Turpin in WNC mountains

>The PRV on the tank does not protect the wood coil if there is a valve between the coil and the tank. If they can be isolated from each another, code would require another PRV in the coil! You can not assume that the valve would always be open.

Bill in WNC mountains

Re: OT----Plastic piping to steel fitting?

#10

Try short lengths of copper pipe

Eddie Pacheco, San Jose, Ca.

>On most pool and spa gas heater installations the inlet and exit pipes tp the heater manifold are done with about a 3ft. length of copper pipe to transition to the PVC spa plumbing. These lengths of pipe help to shield the plastic pipe from the higher temps. of the cast iron heater manifolds which hold the heat for a long period of time after shutdown. The copper pipe, while an excellent heat conductor, does a great job of protecting the PVC. I'm sure a length of galv. pipe to keep the PVC from the heater core will work too. I haven't had any leaks at the plasic to PVC connection. I'm also in favor of the paste or liquid teflon as a thread lube.

Re: OT----Plastic piping to steel fitting?

#11

Re: I thought PVC wasn't rated for hot water.

Gary Evans Tallassee, TN

>Hi Al,

The PVC feeds cold water from the house line into the tank. The tank is connected to the furnace coil with CPVC and the line going to the main water heater is also CPVC.

The water is warmed by the circulation through the furnace coil and then flows from the pre-heat tank to the main water heater. Lots of cheap hot water during the heating season, but these little water leaks are becoming annoying.

I imagine that the expansion of the steel has compressed the plastic fittings somewhat, much like a tenon becomes compressed on a chair rail. Perhaps taking out the fittings, slathering them with teflon liquid and tightening them back down will resolve the problem.

Gary

Re: OT----Plastic piping to steel fitting?

#12

Re: OT----Plastic piping to steel fitting?

Gary Evans Tallassee, TN

>Hi Bill,

Not to worry, there is no valve on the lines connecting the coil and the tank. I have a valve on the inlet line to shut off the water to the system as well as a valve on the tank to drain the system down for maintenance.

Thanks,

Gary

Re: OT----Plastic piping to steel fitting?

#13

Re: OT----Plastic piping to steel fitting?

Gary Evans Tallassee, TN

>Hi Barry,

I think I'll try Eddie's suggestion on using copper pipes to insulate the plastic. I've worked a lot of copper. I don't have the tools to thread pipe, so I wasn't looking forward to working with the steel.

By the way, what are Dresler couplings? I'm not familiar with them.

Thanks,

Gary

Re: OT----Plastic piping to steel fitting?

#14

Re: Teflon tape versus liquid pipe dope...

Gary Evans Tallassee, TN

>Thanks Tim,

More good information.

Gary

Re: OT----Plastic piping to steel fitting?

#15

Re: Try short lengths of copper pipe

Gary Evans Tallassee, TN

>Hi Eddie,

Thanks a lot for the suggestion about copper insulating pipes. I happen to have 10' of 3/4" pipe laying out here that I used the other day to help rescue the cat. Just need to buy a few fittings, some teflon thread dope and I'm there.

Thanks to everyone for their input.

Gary

Re: OT----Plastic piping to steel fitting?

#16

Re: OT----Plastic piping to steel fitting?

Barry Irby

>Dresler couplings are a type where the pipe slips into both ends and then you tighten a cap that compresses a feral around the pipe. They are not Identical to compression fittings. The ones I've seen are longer, about four inches for 1/2" and about six inches for 3/4. I see them used for repairs more than anything else. Yu can cut out the bulge in a frozen copper pipe, slip on a Dresler coupling and tighten it. I have no Idea if they work over a wide temperature range or not.

Try some copper between the plastic and the heater. It may "temper" the temperature swings.

Re: OT----Plastic piping to steel fitting?

#17

Aha! I always thought so!

John in New Mexico

>