Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Shop cabinets

Posts

Shop cabinets

#1

Shop cabinets

Stan Simmons

>I'm planning on building shop cabinets by creating 2 X 8 X 2 boxes with the sides being 3/4" plywood (1/4" back, faceframes, etc.). I was planning on putting them side by side so the walls would effectively be 1 1/2" plywood.

If I do that, will I need a fixed shelf in the middle to prevent bowing?

Also, is going the 2 3/4" plywood sides justified over 1 3/4" and a fixed shelf? Plywood cost would be way down...

Stan

Re: Shop cabinets

#2

Ellis Walentine

It's a little tough to get a handle ...

Ellis Walentine

>... on the question here, Stan. It sounds like you're thinking of making several tall cabinets out of plywood and you're wondering about the need for some kind of stiffening shelves in the middle of the modules. If so, I'd say don't worry about it.

Ellis Walentine, Host

Re: Shop cabinets

#3

Re: It's a little tough to get a handle ...

Stan Simmons

>Ellis,

Thanks for advice... What's your thoughts on going with just a 3/4" wall between units v. doubling up with 2 3/4" sheets of plywood back-to-back. It seems that 2 back-to-back would be more rigid (and simplify construction), but possibly overkill??

Re: Shop cabinets

#4

Re: It's a little tough to get a handle ...

Dave Morris

>Stan, I made a whole wall full of shop cabinets like you are talking about, only they are 4 feet high and 3 feet wide each, and hung them 4 feet off the ground. This left room for dedicated storage areas underneath the cabinets for larger items. Double flat panel doors on each cabinet. Plus a final 6 foot tall floor cabinet on one end of the row, with double doors over double doors and a fixed shelf attached to the face frame dividing the upper and lower half's. None have moved at all. I doubt yours would either. But with an 8 foot tall cabinet, dividing it into an upper and lower section might not be a bad idea for looks. It also means you can have stuff leaned up against the bottom half of the cabinet and still be able to open the upper doors.

Making each cabinet as a self contained unit will make your job a lot easier if you have to go about the whole project a little piece at a time. Me? I seldom have the time to give several hours in a row to anything wood related, let alone a whole project from start to finish of construction. Plus, if you ever move and want to take them with you, it's a simple thing to unscrew them from each other and set them back up again in the new location.

Dave--- who's wife was very happy with her new storage cabinets, making Dave's world a much happier place as well ;-)

Re: Shop cabinets

#5

Ellis Walentine

Oh, I see...

Ellis Walentine

>...so you are talking about a bigger cabinet with a single vertical divider instead of separate, discrete cabinets. Sure, you can go with the combined unit to save materials, but you won't get it out the door once it's assembled, and it'll be pretty heavy and awkward to manuever around the shop.

That still leaves open the question of a fixed center shelf to stiffen everything up. That probably isn't strictly necessary, but I don't see why you wouldn't want to do it anyhow, unless you want to store tall objects in there. The face frames should give enough stiffness, though.

Ellis

Re: Shop cabinets

#6

Re: Shop cabinets

Barry Irby

>Those are some big boys! How tall is your ceiling? You would need about 8"6"+ to be able to stand them up.

I would consider 2' deep too deep, unless you really need it. Stuff would get lost in the back. 16" would suit me better personally.

I would want them to be movable in case I moved. (It would never happen and if it did I would leave the cabinets behind, but that would not stop me from thinking they should be portable.)

Consider making them with half inch thick sides recessed 3/8" in from the outer edge of the face frames. That would leave a 3/4" gap between the sidewalls of the units when they are side by side. Put a couple of furring strips in the space and screw through them both ways to stiffen and hold the units. Screw the face frames too.

Or you could go �the other way� and build them in place with �� partitions and fabricate the frame in place making them permanent.

Re: Shop cabinets

#7

Thanks for the input

Stan Simmons

>Thanks for the input... I think I'll go with 1/2" sides and no fixed shelf. Almost everything attached with screws (face frames, etc.). I will split the doors. That will be a bit odd, but will fit my needs...

The key to keeping them open is to allow for flexible use. I plan on putting full extension shelves in the lower portions to hold portable tools such as my compressor and cordless drills and to deal with the depth. The upper shelves will be adjustable. I'll build in the shelving for each one to meet a specific need...

There will likely be one full cabinet will be devoted to yard tools - can't get the entire space devoted to woodworking...

Also, the height was a good point... Fortunately I have ~ 20' ceilings in my garage...

I'll post a PS once I have built a couple...