Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

New 14" Bandsaw Tires--- To Glue Or Not To Glue?

Posts

New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#1

New 14" Bandsaw Tires--- To Glue Or Not To Glue?

Dave Morris

>...That is the question.

Seems like all the research I'm finding on re-habbing and fine-tuning bandsaws sez to glue the tires to the wheel when you're putting some new shoes on the saw. The saw in question is a Jet 14", the wheels are already crowned from the factory, and the new tires fit between the *rims* of the wheel on each side of the crown.

Jet didn't include any adhesive with the tires when I ordered them, and said it wasn't needed when I called to ask for some.

So, is glue only needed on larger saws with flat wheels (no crowning of the metal or rim to hold the tire in place)? If I glue on the new skins, what type of adhesive is preferable? Does using glue mean balancing the wheel is more of a necessity, and/or using a jig to grind/sand/cut the rubber to insure concentricity of the tire where it touches the blade? Thanks for clearing up my confusion. I'm simply wondering what's what in this particular case.

BTW-- I'm making progress on this saw resto when I can find a spare hour here and there. So far, it's been fun, but living in a small town can make even the usual things like getting the new bearings pressed a lesson in patience and determination. Grrrr...

Dave--- who, then again, likes a challenge every now and then ;-)

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#2

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glu

jan derr

>I glue my tires because I use 1/8" neoprene ribbon that has to be scarf joited and there's no other way to fasten. I clean the wheels and use super glue. I don't think you have to glue if your tires are a continuous unbroken circle.

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#3

Mine work fine without glue

Jim Swank

>

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#4

Ellis Walentine

Check something first

Ellis Walentine

>If you run the saw without a blade and the tire appears at all loose or appears to separate from the wheel because of the centrifugal force, you need glue. This should not be the case with new, springy rubber. The rims are there to keep the loose tire centered and to prevent it from jumping off.

We've had a lot of discussions on this topic in the past, and you might want to search the archives to get a sense of earlier opinions. I just glued the tires on my old Walker-Turner because the warmth of my woodstove had softened them a bit and they were starting to get floppy (I really should get new ones). My preferred method is to tape a piece of cardboard up behind the wheel and then rotate the wheel while spraying Scotch 77 or other spray adhesive onto the rim. The cardboard catches the overspray. Slip the tire on while the adhesive is still tacky and let it dry.

Ellis Walentine, Host

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#5

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glu

Falberg saw Co

>The only time you'd need to glue is when the tire slides off without it. Urethane tires, if you have the right size, are hard to stretch and the instructions call for heating them before installing, but I favor just clamping the wheel to a bench and wrestling them on. The rubber tires, and I've tried several, tend to fly off under centrifugal force, so you'd probably want to glue them on. Contact cement from the local hardware store works fine, just be sure to thoroughly clean the wheel and tire with laquer thinner first. It helps to brush it on while the tire is half-on, half-off; then slide it on wet. It takes longer to dry, but it works. Urethane tires will totally lose their elasticity if left in the sun to overheat. Once the urethane overheats, its stretch is gone forever, in which case contact cement then makes a good temporary repair. My saws are used mostly outside, so I've had to warn everyone about that. Crowning has nothing to do with holding the tires in place; the composition (rubber/urethane), does. Both rubber and urethane tires are so consistent in thickness that I've never had to true them, nor have I ever seen tires significantly alter the dynamic balance of a wheel. You can see how smooth the tire's weld is by the tracks from the blade on the attached photo. Living in small towns forces one to invent new solutions; make lemonade. Edison didn't have a Home Depot either.


img

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#6

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glu

Michael Wangler in Rochester, NY

>Dave,

I have an old 14" Walker Turner BS. I purchased some new tires and needed some help getting them on. They were tight and thought I was all set. However the bottom tire kept creeping off the wheel. I ended up using double sided tape and inserted small 1x1 inch piece every 3 inches around the tire. I figured that was easier than taking the tire off again. I used a small dowel between the tire and wheel to insert the tape. It did not take that long to do and it has held fine for over a year.

Have fun,

Michael

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#7

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glu

Falberg saw Co

>Michael,

I like the dowel idea. Thanks. That would also make gluing easier, but I'm going to try dbl-sided tape too. Nine ways to skin a cat, eh?

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#8

you do not need glue

robert davis

>

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#9

Do too!

Falberg saw Co

>

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#10

Re: Check something first

Dave Morris

>Thanks, Ellis. I haven't run the saw yet, it's still in pieces scattered around my garage. This weekend's plan is to rehab the enclosed base, rig up the new elect-cord, switch, and a dedicated outlet upstream of the switch for a magnetic base task light. Then I'll start putting the pieces back together and I'll see how the tires seem.

I hadn't thought about ambient heat in the shop. Summer's here can get kinda hot--- we had a whole month over 100�, with a full two weeks over 110�, and the garage can get even warmer than that when it's closed up. Is this going to be something of a problem for unglued rubber tires?

In my defense, I *did* try searching several times using various versions of words including "tire", "rubber", "glue", "bandsaw", and "adhesive". Nothing really came up that related to my question, and I used the last two years or so as a parameter for the message dates. Did I miss an archive search somewhere?

Thanks again!

Dave--- who is adding "bandsaw tires" to his list of Scotch #77 candidates, and thinks they ought to name that stuff "Gluzall"

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#11

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glu

Dave Morris

>Thanks. These tires are rubber. Have you had any problems with rubber compared to urethane concerning heat? And how hot are we talking about--- it reached 117� in the shade here this summer, and my garage can get a lot hotter than that by the end of the day.

Dave--- who has made lemonade using a variety of recipes ... as conditions dictate ;-)

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#12

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glu

Falberg saw Co

>"These tires are rubber. Have you had any problems with rubber compared to urethane concerning heat? And how hot are we talking about--- it reached 117� in the shade here this summer, and my garage can get a lot hotter than that by the end of the day. "

Rubber doesn't seem to mind overheating, it just naturally tends to be *soft* and the three varieties of rubber tire I tried didn't want to stay on the wheels at any temp. There was one that might work but I'm waiting on a re-order of smaller diameter to see if they just wanted to be stretched tighter. The jury's still out on that. Urethane tires have a serious heat issue however (for me). If left in the sun my wheel housings can get up to, I guess, 180*. I'm also guessing that the urethane breaks down before then - at 150*. Again, no real science, just guesswork. Hope it helps.

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glue?

#13

Re: New 14" Bandsaw Tires--- To Glue Or Not To Glu

Dale Stansbery

>I second the tape solution. A few years ago I had a problem with old rubber tires that stretched while running the saw, to the point of gapping off the wheel where the blade wasn't touching and making an incredible roar. I wrapped the wheel with two sided golf grip tape, wet it well with mineral spirits, and easily slid the tire on, just like re-gripping golf clubs. It's held ever since.