Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Table saw box joint; brain lock

Posts

Table saw box joint; brain lock

#1

Table saw box joint; brain lock

Barry Rubenstein

>I've linked a site which describes how to make a table saw box joint jig. I made it and it works really nicely. The instructions clearly describe how to make 1/4" box joints and I mastered that but can't for the life of me figure out how to make 1/2" box joints.

Has anyone made this jig and figured out the 1/2" joint ?

http://www.leestyron.com/newlynnjig.php

Re: Table saw box joint; brain lock

#2

Re: Table saw box joint; brain lock

Al Stokka - Cambridge, Iowa

>Barry,

I haven't built the jig, but it looks as though you would:

Mount blade(s) which will cut a 1/2" kerf. Clamp the four workpieces in the jig with two of the four offset to the right by 1/2" (as opposed to the 1/4" offset used when making 1/4" joints). Make the first cut. Turn the crank exactly two times the number of revolutions turned for a 1/4" box joint after each cut.

Re: Table saw box joint; brain lock

#3

Re: Table saw box joint; brain lock

Barry Rubenstein

>Thanks Al but I tried that and it's not working out. I'm now at the "trial and error" point and it's mostly error.

Re: Table saw box joint; brain lock

#4

Re: Table saw box joint; brain lock

David Hay @ Denver

>How is it not working out? Are the joints close, but just not lining up? Or not even close to lining up? If it's the former, it could be that there's just enough slop in the turning mechanism that a 1/2 joint isn't possible

David

Re: Table saw box joint; brain lock

#5

Jim DeLaney, Austintown, Ohio

Re: Table saw box joint; brain lock

Jim DeLaney, Austintown, Ohio

>Barry,

I have that jig - or at least a very similar one - and what Bill said is exactly right. You can make whatever size you want, just by changing the blade width and the offset.

Note that the kerf size is critical. If your blade setup is off even 1/64", then the joints aren't gonna fit. The threaded rod is 3/8-16, so a full turn moves the carraige exactly 1/16".

Where, for �" joints, you were turning the crank eight turns between cuts, you'll be turning it sixteen turns for �" joints. If your blade setup is exactly half an inch, then you ought to be spot on.

Jim D.

Re: Table saw box joint; brain lock

#6

Great jig...once you get use to it.

Craig Daymon

>I have a similar jig and I always use the same size blade, a 1/8" kerf Freud Rip blade (because it has a flat top tooth). The rod is 3/8"-16, so 2 revolutions moves the cut 1/8" more. If I want 1/2" teeth, I cut, turn twice, cut, turn twice, cut, turn twice, cut. That's 4 cuts with a 1/8" kerf giving me a 1/2" opening. Now I turn twice more to get past my last cut position for the opening. Then I turn the handle 8 times to move 1/2" without cutting, to the next position I want to cut. Just repeat the process as necessary.

For the joining board, Turn 8 times, moving the first cut position 1/2" (or eight 1/16ths), before making your first cut to start. It might help to make a sketch and write down your required turns. That's what I did for my desk organizer where I varied the width of the teeth.

For me, it's less about the width of the blade and more about how much I move my cut with each turn. The width only comes into play when moving over uncut areas to the next starting position.

-Craig

Re: Table saw box joint; brain lock

#7

Re: Great jig...once you get use to it.

Barry Rubenstein

>My attempt at a 1/2" joint was off a little, so maybe it has to do with the slop in the jig.

Re: Table saw box joint; brain lock

#8

Re: Great jig...once you get use to it.

Craig Daymon

>If each tooth was off (hopefully big) by just a little, it is possible with this jig to run it through again and just shave the required fraction off each tooth. I added a spring between the handle and the jig someplace (not in the shop to look right now) to take out some of the slop.

When I build my next one, I'm thinking about making the investment in an Acme threaded rod, which I think are suppose to have tighter tolerances. I'm thinking over a router indexing rig, that would let me do Incra/Jointech things, using threaded rod.

-Craig