Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Kickback - ouch!

Posts

Kickback - ouch!

#1

Kickback - ouch!

Mark in B'ham

>I made a promise to myself that I would confess on WC if I did something stupid and got hurt at it. But yesterday I got hurt but I thought I was doing everything right. So, I thought I would get y'all to correct my thinking.

Here is what happened. I was cutting out 3 1/2 inch squares from 1X6 stock on the TS. I set the fence and crosscut the board to get all the pieces the right length. Then I set up a featherboard just in front of the blade and used a push stick to send the pieces through to square them up. On the third one, the offcut got picked up by the blade and shot back at me. It hit my hand and caused a big bruise on two fingers and my knuckle. Nothing seems broken and I can move it fine.

So what do you think I should have done to help prevent this? As always, TIA

Mark

Re: Kickback - ouch!

#2

Re: Kickback - ouch!

Alan Tolchinsky

>We're you using the fence to keep all the pieces the same length? If yes, I would have used an auxilary fence on your main fence. That way when you made the cut, the offcut would have no contact with the fence. Trapping the offcut between fence and blade will result in a kickback. Sorry for your accident and I hope you heal fast.

Re: Kickback - ouch!

#3

Re: Kickback - ouch!

David Hay @ Denver

>Sounds like the problem was trying to use the miter gauge and the fence at the same time. The offcut got caught between the blade and the fence and was shot back at you.

In the future, you should either clamp a block to the fence in front of the blade, or slide the fence back (in the case of the Unifence). This allows you use the fence to register the piece and ensure uniform sizes, but keeps the workpiece from riding along the fence when it's actually being cut.

David

Re: Kickback - ouch!

#4

Re: Kickback - ouch!

Mark in B'ham

>Nope, the offcut was on the left side of the blade, the fence and the workpiece were on the right side. I pushed the workpiece with a pushstick.

But that brings up a good point. Perhaps, I could have used the miter gauge with a long extension board to push the piece AND the offcut past the blade.

Re: Kickback - ouch!

#5

Re: Kickback - ouch!

Norman (Ottawa, Ont.)

>I looked at your procedure and wonder why you didn't just square the 1X6 board up first, and rip it down to 3.5 inches.

Then I would cross-cut the smaller 3.5 in. pieces from the longer board. You don't need to run small square piexecs into the blade this way.

Adding an auxiliary fence to end before the blade is a very good idea, in fact is the procedure that I use here when cross-cutting small pieces with a Unifence.

Norman

Re: Kickback - ouch!

#6

Wrong application for a fence!

Lee Schierer, McKean, PA

>Cutting a piece that was 3-1/2 X 6 using the fence is always asking for trouble. You don't have enough length against the fence to prevent the part from wanting to rotate. The safety rule here is the length of the piece along the fence should always be 1-1/2 to 2 times the width between the fence and the blade.

The better method would be to use crosscut sled with a stop block on the fence set 3-1/2" from the blade. You will also need a clamp to hold the piece being cut in place as I would not recommend putting your fingers within 3-1/2" of the blade. This will insure every piece is exactly the same length and the off cut is free to do what it wants as it is cut off.

Lee

Re: Kickback - ouch!

#7

Can you clarify a bit

Stephen Kirk in Quakertown PA

>It sounds like you have the fence set to the right of the blade, 3 1/2" off. You are then pushing rectangular pieces agains the fence with the short side of the rectangle against the fence. Then what happened is an offcut, which would be to the left of the blade was somehow grabbed by the teeth and shot backwards?

If that is the way it happened, then I agree with everyone else. you are better off using the miter gauge (or crosscut sled), setting a stop block at the front of the fence and using that to correctly size each piece.

As to why the offcut was caught by the blade and thrown, I'm not sure. If you are using hardwood, could the offcut have flexed in (as reaction would can) and then once you cut far enough through it let go and took off? Was there any burning on the piece or offcut?

Re: Kickback - ouch!

#8

Re: Kickback - ouch!

Jerry Nicholson

>I agree with Norman on how this should have been done. I did the same thing trying to cut a 4 x 4 piece of 1/8 inch aluminum (lens board for a a photo enlarger) on my table saw. The workpiece kicked back and hit me square in the stomach (of course I shouldn't have been standing right behind it) and my immediate thought was "this could be a bad thing". I started to unbutton my shirt to check the damage and blood began showing up all over the front of my shirt. I discovered a nasty abrasion on my stomach but no guts hanging out. The blood was from a gash on my thumb that I hadn't even noticed yet!

Am I smarter now? Well...... maybe. I don't use an enlarger any more.

Jerry

Re: Kickback - ouch!

#9

A cautionary tale

Robert Henderson

>Just over three years ago I did something similar.

I was cutting some 2X4 stock to length (about 3 inches) by running them through the table saw between the blade and the fence (with my hand, no push stick).

I wanted to save a trip to Home Depot for another 2x4.

The blade hit a knot and the piece of wood twisted and shot back into my hand at 120 MPH. It then shot past me and through a window.

The bade was a twisted wreck and I ended up in the emergency room.

I was incredibly lucky. Nothing broken; nothing cut off, although it took two years before my hand stopped hurting all the time.

To save 3 bucks and a car trip I spent $200 on the emergency room and had to replace a saw blade. I have scars and a hand that aches whenever it gets cold. Nevertheless, when I think of what could have been the results I consider it a cheap lesson.

I keep the twisted blade and the chuck of wood as a reminder.

I have now developed a finely honed sense of danger.

Before I do anything with power tools I walk through the process in my head. If I get the least little sense of fear I figure out another way of doing the job, prefereably with a sled with clamps, but at the very least with a looong push stick.

Re: Kickback - ouch!

#10

Use a spacer

Charles Sharp

>Cut a 1" spacer and set it beside the fence. Bump your stock against it, and clamp the stock to the miter fence. Remove the spacer, (now you piece is 1" away from the fence) and make your cut.

NEVER, EVER, EVER, USE BOTH THE MITER GAGE AND FENCE WHEN YOU HAVE YOUR MITER GAGE ON ONE SIDE OF THE BLADE AND YOUR FENCE ON THE OTHER SIDE OF THE BLADE (unless you use a spacer as noted above).

Re: Kickback - ouch!

#11

Re: Kickback - ouch!

Jim Dillon

>Mark,

First, glad nothing was seriously hurt, except your pride. I agree with all the others and would add that the featherboard might have actually exacerbated the problem. If I understand you right, you used a featherboard to hold the 3 1/2 inch end of the 6 inch long piece against the fence. And that you were pushing with a pushstick on the long side between the fence and blade. Perhaps as the narrow end passed the featherboard, the tension was suddenly released causing the piece to rotate slightly and be caught by the spinning blade. Whereas the pushstick side made it through OK, but that is more due to blind luck than anything else. As others have said, never try to crosscut very narrow pieces using the fence alone. Others have made excellent suggestion for how to do this much more safely.

Jim

Re: Kickback - ouch!

#12

Bart Goldberg

Get A GRR-Ripper -

Bart Goldberg

>

Re: Kickback - ouch!

#13

Re: Kickback - ouch!

Mark inb'ham

>Sorry for not checking back very quickly. We have had some bad weather around here. Had to go get the kids from daycare. Everything is okay for us, but there have been some fatalities in nearby communities.

Thanks for all your suggestions. Stephen, you summed up what I did exactly. This may prompt me to finally build a crosscut sled. Thanks again, and as they used to say on Hill St. Blues, Let's be careful out there.

Re: Kickback - ouch!

#14

Re: Agree with Bart - I always use GR-Rippers

Larry Clinton At Frankfort (Central)., Indiana

>

Re: Kickback - ouch!

#15

Jesper, Denmark

Re: Wrong technique......

Jesper, Denmark

>You should have ripped the board to dimension first, then crosscut with a sled - no fence.

Re: Kickback - ouch!

#16

Re: Kickback - ouch!

DB

>Use a miter saw to cross cut a board or a miter gauge on the table saw. The rip fence (the correct term) on the table saw is for ripping only.