Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Hide Glue Question

Posts

Hide Glue Question

#1

Hide Glue Question

Thomas Skaggs, Foothills of Mount Level

>My veneering work has been limited to date. Right now I am working with panels that get lots of small pieces of veneer applied. I am currently using Titebond for Veneer glue. Once applied to the veneer it causes the veneer to curl. Does hide glue also cause veneer to curl as much?

Thanks

Tom

Re: Hide Glue Question

#2

don't know exactly

Tom Sontag - St. Louis

>and surely someone experienced will have direct answer soon. But I DO know that veneerers frequently keep a spritz bottle nearby to moisten the other side of veneer as they work to control curling.

Do we get to ask or do we have to wait for the final pics?

Re: Hide Glue Question

#3

Re: don't know exactly

Thomas Skaggs, Foothills of Mount Level

>I hadn't thought about moistening the top sides. That might help.

These panels are an experiment for me. They are panels for cabinet doors. I am creating them to have the design idea of stained glass. Essentially different woods with raised ebonized "cames" between all the pieces. Challenging to say the least.

Thanks Tom!

T.

Re: Hide Glue Question

#4

Re: Hide Glue Question

Tom Stockton

>Tom

Don't know about hide glue but I was always taught to apply the glue to the substrate only to prevent the problem of curling.

Tom

Re: Hide Glue Question

#5

Re: Hide Glue Question

Thomas Skaggs, Foothills of Mount Level

>Shows you how much veneering I have done! I wasn't sure. I've been concerned about getting good adhesion so, as with solid wood, I've been glueing both surfaces.

Thanks for that info.

Tom

Re: Hide Glue Question

#6

Re: Hide Glue Question

jmohnike

>Have had better luck with Hot hide glue. Sets up fast and no moisture problems.

Have also some luck with contact cement, but if you apply it too thick it can creep on you.

Joe

Re: Hide Glue Question

#7

ooooooo...

Tom Sontag - St. Louis

>I like the idea. In fact, (and I know every designer hates to hear this, but) I have had ideas along similar lines. I guess since we both have done stained glass stuff, it is a natural progression. Pull it off though, and you'd be da man!

Re: Hide Glue Question

#8

Lee Grindinger

It can be very difficult

Lee Grindinger

>Burls, other figured woods, and marquetry/parquetry patterns can go wild when moisture hits them. Hammer veneering entails applying hot hide glue to both sides which helps some but not entirely since figured woods and burls expand in different directions. Some pieced together veneers need refitting while applying since it's impossible to un-expand them. I've had to recut seams to accommodate this expanision when hammer veneering and have pretty much quit using this method unles it's a small area and I've got some glue ready. The up side to hammer veneering is that as long as there's water and heat there's no rush or time limit as there is with PVA.

The easiest way is to get a press. A vacuum press is a great investment if you're going to use veneers a lot. In fact, Tommy, in your case the purchase of a vacuum press WILL change the way you design and build furniture for the better.

Lee

Re: Hide Glue Question

#9

Lee Grindinger

A show I'd pay to see...,

Lee Grindinger

>A show I'd pay to see is W. Patrick Edwards laying up an elaborate top such as one of those two round "twin" tables posted here a while back. Perhaps Ellis could dig that pic out and repost it.

Ellis, you seeing this?

Lee

Re: Hide Glue Question

#10

Re: Hide Glue Question

Tom Stockton

>Tom

If you wanted a tour of my learning mistakes it would take a while. The info about why you only want to put glue on the substrate came from Tage Frid's second book. I wish I knew a good book that is current to recamend because things have changed a lot since his book was published but I would think that the videos by Vacupressing sytems are a good start. Take Lee's advice get a vacuum press it makes veneering fairly painless. Hammer veneering has its place and there are things you can do with the technique you really couldn't do otherwise but for veneering flat panels and curved work vacuum presses really shine. Stay away from contact adhesives they will just make your life painful in the long run they work well with the paper backed veneers but you should be using high quality raw veneers for the type of work you do.

Tom

Re: Hide Glue Question

#11

Re: Hide Glue Question

Hank Knight from SC

>Thomas,

I've done some hammer veneering with hot hide glue. I wrap the veneer in wet (not sopping wet - just wet) paper towels for 30 to 45 minutes before applying the glue. It seems relax the veneer and keep it from curling. I also understand that a little glycerine added to water applied to veneer before the glue-up softens it and prevents curling. I think you spray it on with a spray bottle. I've never tried this, so I can't validate it from personal experinece, but the wet paper towels work for me.

Hank

Re: Hide Glue Question

#12

Alan Young

You mean these? *LINK*

Alan Young

>Click "Most Recent Work" from the link below.




Patrick Edwards phenominal Tables

Re: Hide Glue Question

#13

Child's Play

Thomas Skaggs, Foothills of Mount Level

>Gee....That Edwards guy's tables look like a stroll in the park compared to this project I'm doing. Maybe when I get done with this project I'll prove it by replicating those tables while blindfolded.

Tommy

Re: Hide Glue Question

#14

Lee Grindinger

Yup, that's them

Lee Grindinger

>