Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Clamp Storage Rack PICS needed.

Posts

Clamp Storage Rack PICS needed.

#1

Clamp Storage Rack PICS needed.

Ray Carson in Lawrenceville, NJ

>Hey ya'll,

I've looked through my archive of woodworking magazines and believe or not I've only found a couple of clamp racks to get ideas from. As everyone knows, a woodworking shop is always evolving and I'm finally getting around to getting the clamps organized instead of piling them up on the floor. I can't deal with it anymore. :-)

Would the gang mind posting some PICs of their rack.? My shop is in the basement and I have limited wall and floor space. A mobile rack would be nice but not necessary. I would consider hanging them from the floor joists but am leary with the kids jumping up and down on the floor above. My luck would be finding a pile of clamps laying across my table saw or a nearly finished project with some nice dings and dents.

I own Bessey's, 3/4" and some 1" pipe clamps, those lightweight Jorgies and spring clamps. All different lengths.

Thank you.

Your woodworking pal in NJ,

Ray

Re: Clamp Storage Rack PICS needed.

#2

Re: Clamp Storage Rack PICS needed.

awh

>I built a �New Yankee� inspired mobile clamp cart. It holds all my clamps; bar, spring, C, quick-grips, hand screws, etc. that way I know where they are! If I were to go it again I would make it a little wider to allow for future additions, as it is now it�s pretty pack front and back.

Tony Haukap

Home Page - http://www.cyberspace.org/~awh/

--


img

Re: Clamp Storage Rack PICS needed.

#3

Here are a couple of versions…

Rod Peterson -- Ormond Beach

>The first is one I built from a plan from Woodshop News perhaps ten years ago:




My original clamp stand.



As my K-Body collection grew, it became inadequate. Then last year I got around to building The New Yankee Workshop pattern stand.






Norm Abram model clamp rack.



I like it a lot. For the footprint (around 4 ft2) it provides a tremendous amount of storage. Build it beefy, because it is quite heavy when loaded. It also tends to be a little top heavy, which is somewhat mitigated by the angled uprights, however you do have to pay attention and lend a hand if you need to roll over any debris. Larger, urethane wheels would probably help.

I actually still need to build some interior braces for additional storage (Quick-Grips, handscrews, etc.), but it accommodates so much more hardware than the original, it's taken a lot of pressure off my spare wall space.

Rod

Re: Clamp Storage Rack PICS needed.

#4

I'd go over head anyway.....

SanMan

>.....if you use some hangers with a lip on them, I doubt you'd have a problem with them slipping off.

Just an idea.

SM

Re: Clamp Storage Rack PICS needed.

#5

Re: Clamp Storage Rack PICS needed.

George@Colonel's Workshop-Havertown PA

>Good Afternoon Ray,

Mine is on the order of Rod's picture, only without all his K Bodies. I prefer other designs. However, the rack holds a lot of clamps. What he says about weight and mobility is true of mine. As my rack is tucked between the wall and the washing machine, it isn't really very mobile for lack of space. I wind up leaning behind the rack to retreive and return my pipe and bar clamps. What a PITA! I think the best rack is enough side by side wall space and a couple long hangers. I've asked SWMBO for the area now occupied by her washer in exchange for a new washboard. I extolled the merits of energy savings and efficient space utilization, and darn if she didn't throw a 10" C-Clamp at me! Women can be hard to understand sometimes.

George

Re: Clamp Storage Rack PICS needed.

#6

Re: Clamp Storage Rack PICS needed.

Ray Newman

>Like others, I built the New Yankee version.

the only modification was that I added soem ineterrior shelves to hold smaller clamps, glue, biscuits, glue brushes, etc.

If do build a "mobile" cart, don't skimp on the casters. I have 4" casters & I know wish I installed the 6" HD urethane(?) tyred casters. The casrt is ehavy when laoded up.

Re: Clamp Storage Rack PICS needed.

#7

Stupid question about these racks...

Joe in a Cleveland suburb

>I know this will sound really stupid but what keeps the clamps from falling off these racks? Like Rod's? I would think they would just slip right off. Do you clamp the clamps on or what?

Thanks.

Joe

Re: Clamp Storage Rack PICS needed.

#8

Lee Gordon

Re: Stupid question about these racks...

Lee Gordon

>That's exactly right. You clamp them on and they stay put. Also, because the clamp racks patterned after Norm's are an A-frame design, they lean in toward the top and that also helps keep the clamps in place.

Re: Clamp Storage Rack PICS needed.

#9

The angle of the dangle…

Rod Peterson -- Ormond Beach

>I can't remember the exact angle—it's not much—but as I recall, the base of the “A” frame tapers from approximately 24" (outside measure) to about 12". It's not much, but between that angle and the cross supports which the bars rest against, it's enough to keep everything hanging happily. It's very stable. No clamping is needed.

As Norm did on the project, it helps to lay things out so you can space the cross supports properly to accommodate your particular collection of clamps. I took extra care so as to ensure I had enough room to hang 24"ers both at the top and halfway down to allow for the embarrassment of riches I have in that size. It's not easy to fit 12"ers, 24"ers, 40"ers, and 50"ers all on the same setup. I don't know what Tommy would do with that pair of 96"ers he has. The rack isn't that high.

As Ray said, I wish I had gone with 5 or 6" urethane casters instead of the 4" hard rubber I did use.

Rod

Re: Clamp Storage Rack PICS needed.

#10

Re: The angle of the dangle�

awh

>He�s the sketch I put together when I built mine. The angle is 5-degrees. It�s made from 1x4�s but instead of pocket screw joinery that Norm used, I used half-lap joints. And like Rod I wanted to be able to hang 24� Bessey top & bottom so that kind of dictated the overall height, the back side has 12�, 18� & 24� Bessey clamps and various clamps hang on dowels between the ladder frames and on the sides. There is a shelf midway that holds glue, brushed, biscuits, etc. and another shelf at the bottom. A back of napkin calculation shows that the entire unit loaded weights about 380 lbs (that includes the wood frame). It has 3-1/2� casters and rolls fine, but I�ve come to the conclusion that caster quality and ratings very greatly!

Tony Haukap

Home Page - http://www.cyberspace.org/~awh/

--


img

Re: Clamp Storage Rack PICS needed.

#11

Re: Clamp rack PICS - Thanks everyone!

Ray Carson, New Jersey

>Seems a few of you are big fans of the "Norm" rack. :-)

It's a nice design and I may incorporate some of that design into mine. I also like the round one Rod built. Seems to take up less room. I guees I'll have to draw a "sketch" like -awh- did. Some sketch!

Thanks for the PICS, they should help.

Ray

Re: Clamp Storage Rack PICS needed.

#12

Re: The angle of the dangle�

awh

>A couple more (fuzzy) front/back pictures - it�s clear (no pun intended) I need a better camera!

Tony Haukap

Home Page - http://www.cyberspace.org/~awh/

--










Re: Clamp Storage Rack PICS needed.

#13

Re: Clamp rack PICS - Thanks everyone!

stevo wis

>I also built the cart and use it, but in addition I built some racks from the light angle iron used to mount garage door openers. I ran two pieces app. 18" long horizontally from the wall. The clamps slide and hang between the two angle irons. I repeated this about 4 times. I bolted more angle to the joists above to hold them up. Because I can now stack about 15 clamps deep away from the wall, it takes very little space. Sorry I dont have a picture, but it works well, and I can store upwards of 50 or so, in a space about 3 feet wide, and 18" from the wall. If more info is wanted let me know.

stevo

Re: Clamp Storage Rack PICS needed.

#14

Thanks

Joe in a Cleveland suburb

>