Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Poor mans mortises

Posts

Poor mans mortises

#1

Poor mans mortises

Stephen Kirk in Quakertown, PA

>I'm building a workbench for a friend and I'm using standard 2x lumber, so I'll be gluing up 2 pieces for the legs. I'm using mortise and tenon joinery to provide good strength. Normally, we'd glue up the legs and then drill/rout/chop the mortise. But, I figured, why not lay out the mortise location on the inside of each leg half and then rout out half the width of the full mortise. I freehand rout close to my lines to the depth I need (which will turn into the width of the mortise when the two halves are put together). Then I come back with a chisel to clean up the edges. I found that the router leaves a nice smooth cut on what will end up being the wall of the mortise, where you want a good surface. All in all, a fast way to cut them I found. Working freehand can really save some time, not having to set up fences and such. If you stay close to the line, there isn't much clean up to do with the chisels.

Some of my mortises are even stepped, and these were easy to cut this way. If anyone else ever does glued up legs with mortises, maybe this is worth considering.

Re: Poor mans mortises

#2

Ellis Walentine

Yet another way to do it...

Ellis Walentine

>...is to laminate your legs from three pieces of wood and just leave out the center layer where you want the mortises.

Ellis

Re: Poor mans mortises

#3

I have done that before

Stephen Kirk in Quakertown, PA

>On another project I tried the 3 piece method. It is also very easy to do. A good planing and glue up makes the joint very difficult to notice too. I believe I stood the middle board on end against the miter gauge on the table saw and cut out the shape of the mortise with a dado blade. Stepped tenons would be easy this using a simple stop block to locate the steps, and then just change the blade height.

I tell ya, one of the fun parts of woodworking is finding that there are often a lot of ways to do the same job.

Re: Poor mans mortises

#4

Ellis Walentine

The three part method

Ellis Walentine

>The idea I was getting at was to use a middle layer that is the same thickness as the tenon. That way, there is no cutting to do at all except to crosscut the pieces. Make the rail the same way, with the tenon layer made of the same thickness as the mortise layer. No routing or sawing required at all.

Ellis

Re: Poor mans mortises

#5

This sounds like a through tenon, right?

Tim Greif - West of Chicago

>I can't see how this three part glueup would allow you to do a mortise that didn't go all the way through the leg. Am I reading this correctly?

Re: Poor mans mortises

#6

Re: This sounds like a through tenon, right?

David Hay @ Denver

>If you don't want the look of a through tenon (e.g. no end-grain), you could make the middle lamination out of three pieces...top, bottom and a thinner section that covers the end of the tenon.

David

Re: Poor mans mortises

#7

Re: This sounds like a through tenon, right?

Barry Irby

>I made some mortises for a bed I was working on recently. The legs were three thicknesses and the cross pieces were a single piece.

I cut a notch in the center lamination of the legs that fit the ends of the cross pieces.

Then, to allow the cross pieces to float or expand and contract (widthwise) I cut 1/4" by 1/4" slots in all three laminations and on both sides of the center lamination. I cut a matching slot across the ends of the cross rails. Then I put it all together with 1/2" by 1/4" splines in the slots.

I glued the splines into the laminations of the three layers of the legs, but left the mortises dry. The splines lock the ends of the rails into the joints very securely, but allow them to change width seasonally.

This was much easier to do than to describe. Use a quarter inch Dado blade to cut the slots. Cross cut the ends of the rails and then trimmed the ends back to drop into the mortises.

Re: Poor mans mortises

#8

Ellis Walentine

Yes. A through tenon.

Ellis Walentine

>If you want a blind tenon, make the center lamination out of one length of wood and bandsaw a notch where you want the mortise. This method is a little more complicated than the chopsaw method, but it still saves you from having to cut mortises by hand or rout them.

Ellis