Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

2 speed planers

Posts

2 speed planers

#1

2 speed planers

Allen Bryant - Bumpass, VA

>Well, some of you may remember that last fall my planer caught fire. The resulting investigation proved that the motor had overheated to the point that it melted the windings and started the fire. The planer is repairable, but even just replacing the functional parts is almost as expensive as a new one. Since I bought the planer used in 1996, I've decided to replace it. Unfortuantely my shop is way too small to handle a large planer so another lunch box style will have to be used. My question is, for those of you that have the 2 speed planers either dewalt or delta, do you find that you use it enough to make it worth getting or should I put the money into maybe a better single speed planer.

Re: 2 speed planers

#2

Re: 2 speed planers

Tony - Memphis

>I bought the DeWalt 735 a while back. It cuts really well on the fast setting, but I can tell a difference on the slower speed. I can't argue that its worth any extra money, but I sure do like the planer. I replaced an old Delta.

Tony

Re: 2 speed planers

#3

Re: 2 speed planers

arw01

>The DW735 lives in my garage also. I used both speeds, if I'm only working a few boards I will just leave it on low speed, and the finish is tremendous out of that planer.

When there is a lot of work to do, I will run on high speed to start getting close. Then I will allow those boards a few days to acclimate to their new thinness before switching back to low speed.

Some complain the knives are so expensive that it pays to buy a cheaper planer with cheaper knives. I've not yet rotated my first set, there are a few knicks, but just a few seconds with a scraper or 220 grit knocks them off.

Alan

Re: 2 speed planers

#4

Re: 2 speed planers

Clay Foster

>I have a 24" big iron planer and a DeWalt 2 speed. I've also owned a Delta 2 speed lunch box. The big iron will remove wood fast, the lunch boxes produce a superior surface at the slow feed rate.

If I could only keep one, it would be the lunch box. Whether or not it has two speeds would be irrelevant in my decision. The time spent watching wood slowly creep through at the slow rate is time I won't be spending scraping and sanding.

If you plane hundreds of board feet a day, get a bigger paner with a bigger motor so you won't burn it up again.

Re: 2 speed planers

#5

Re: 2 speed planers

Jerry Burns

>I just replaced the knifes on my 735 after two years and 3000+bdft of maple ,cherry and oak I use both speeds get close in high speed then switch to low speed.I replaed an old Ryobi planer that had burnt up the same way as yours and yes it was used when I got it.I still have the beast stored under the wood shelf ayn one need parts ? Before I toss it

Re: 2 speed planers

#6

Re: 2 speed planers

Tony Sade (Charleston, WV)

>I've had the delta 2 speed for a few years and love it. I think having two speeds is a definite advantage. Odd thing is, I've just run a bunch of soft maple that I'm using for a computer desk, and on some of the pieces that had spots of somewhat "squirrely" grain, the faster speed actually left a cleaner finish. That's generally not the case, of course, and there's a notable advantage to having the slower speed, IMHO.

I got it during a Lowe's special for about half the normal price, but I'd buy it again at full price (or at least the cheapest price I could find) if I had to. Never used the Dewalt.

HTH,

Tony

Re: 2 speed planers

#7

JL

Re: 2 speed planers

JL

>I've got the Dewalt DW735 2 speed. I like it. If you do buy one, I recommend getting the auxilliary "tables" for infeed and outfeed. They reduce the snipe.

Re: 2 speed planers

#8

Delta...love it....would buy another one.

Terry Alexander

>

Re: 2 speed planers

#9

Re: 2 speed planers

John Lucas

>I love my DW735 but as long as the blades are sharp I haven't been able to tell the difference between low speed and high speed. It sure does cut better than my old Delta.

Re: 2 speed planers

#10

Re: 2 speed planers

Denis Ch�nard, Orl�ans, Ont.

>Got the Delta, love it, and I use both speeds regularly.

Very good machine, I'd buy it again in a heartbeat.

The knives don't seem to last that long though. I mean, they still cut, but the quality goes down after a while and the motor seems to work harder. To compensate, when the knives start to dull I switch to the lower feed speed.

I've kept my old Delta 22-540 to do the grunt work, since it's not worth much anymore on the market. That lessens the wear on the two speed machine, and the old planer's knifes are resharpenable, keeping the costs down. Now all I have to do is arrange a setup where both planers can be used without taking too much space...

DC

Re: 2 speed planers

#11

Re: 2 speed planers

Gary Ratajczak

>I just replaced an older Dewalt 733 with the 2 speed 735. I ran some short tiger maple pieces through the 735 at slow speed. Very nice finish - couldn't do that on my 733.

I also ordered the In/Out tables - Amazon was the lowest.

My Home Depot has teh 735 for $499.00. Lowes is $549.00, but they will do a price match +10%. In addition, local Lowes has a $60.00 off or cash back card - not sure - one or the other.

Infinity Tools has higher quality replacement knives. I keep hearing about short life, but there seems to be more like the above poster that have run 1000's of feet through. I think it's how much you try and hog off at a time.

I lied the 735 in that it does an automatic height lock - no need to clamp or use the knuckle buster bar!!

Good luck.

Re: 2 speed planers

#12

I have the Delta as well

Stephen Kirk in Quakertown PA

>And it performs beautifully for me. I too notice that the blades seem to dull more quickly than some others. It think it does depend a lot on what you are doing - I work with lots of Oak. The Delta has reversible knives, so you get 2 lives on each blade. I never did bother to estimate what I've fed through it.

Cleaning the rollers is a pain, you have to keep cylcing the machine, but it's pretty minor in the grand scheme of things.

All in all, good machine for it's price, and I've been happy. The slow speed gives me a nice finish. With sharp knives and good wood, the fast speed leaves a decent finish too.

Re: 2 speed planers

#13

Delta Feed Problems?

Allen Bryant - Bumpass, VA

>For those of you that have the delta? any response to the feed problems that seem to pop up in the reviews quite often?

Re: 2 speed planers

#14

Allen - check your Email

David Yoho

>

Re: 2 speed planers

#15

Re: 2 speed planers

Stuart Hough

>I've got the Delta 22-580 2 speed. I love the thing! Ihave used both speeds and can tell a minute difference on the slower feed speed. I use it for final dimensioning only.

Re: 2 speed planers

#16

Re: 2 speed planers

Stuart Hough

>I've got the Delta 22-580 2 speed. I love the thing! I have used both speeds and can tell a minute difference on the slower feed speed. I use it for final dimensioning only.