Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

wood vaneer on MDF

Posts

wood vaneer on MDF

#1

wood vaneer on MDF

Wayne Carson

>I am making a old time Ice Box and have to make some pannels and am thinking of making the pannels out of MDF covered with quarter sawn white oak and gluing it to the MDF with hide glue. I made a test piece and it seems to work out fine anything I need to know about the MDF??

Re: wood vaneer on MDF

#2

Re: wood vaneer on MDF

Barry Irby

>I think you need to veneer both sides of the panel for "balance". Other wise it will warp when the humidity changes. Probably most any white oak veneer will be OK for the other side, not necessarily QSWO, but even that might be "better".

Some MDF is subject to failing if wet. I don't know if you plan to actually use the IceBox, but don't get the MDF wet.

Re: wood vaneer on MDF

#3

Re: wood vaneer on MDF

Tony - Memphis

>Everybody always says you must veneer both sides, but I've done many panels on one side only and not had any issues at all. Sounds like you have a good plan. Before I got a vac setup, I used melamine and cauls and lots of clamps. I used plastic tarp as a non-stick barrier between the platens and the veneer. If you plan to stain, do some testing. The veneered panels may take stain differently than the solid pieces. Nothing special about the mdf (other than it is dusty). I usually make my panels a bit oversized and then cut them down. The veneer almost always shifts a little when gluing it down. MDF glues up really well, though the rough cuts absorb some glue, so make sure you use plenty. Good luck with your ice box.

Tony

Re: wood vaneer on MDF

#4

Re: wood vaneer on MDF

Doug in Denver

>Whether you veneer both sides depends on a couple things. First, will the inside show when you open the box - in other words, do you need to veneer both sides for appearance?

Even 3/4" MDF will warp if veneered on one side. If it will warp, it usally does it in a day or two. I did some drawer fronts recently and they bowed, but since I was gluing them to a drawer box, it did not matter. However, If I'm using thin MDF that will go in a frame held on all sides (like a small door), I usually only do one side, but I normally start with mdf that has already been veneered. If I were you, I'd buy oak veneered MDF, then glue the better looking veneer on one side only if these panels are thin, and will be held in place by a frame. If your are using thick MDF, then veneer both sides no matter what you start with, because if it warps, your frame will not hold it staight.

Re: wood vaneer on MDF

#5

How about curved section MDF and veneer?

Mark McC

>I have a round table to make, with a 4 section circular skirt.

I have done this using the thin strip laminating method of clamping the sections to a cruved jig before.,,,really time consuming and hate process.

Cutting the curves sections out of sold wood is too wasteful and too expensive.

What about cutting the curved pieces out of laminated MDF and then veneering the front of the MDF?

Sounds like allot of guys have used MDF + veneer, appreciate your opinions.

Mark

Re: wood vaneer on MDF

#6

Re: How about curved section MDF and veneer?

Doug in Denver

>Ne reason you can't do that, but why is gluing up an mdf laminate easier than a solid wood laminate?

Re: wood vaneer on MDF

#7

Re: wood vaneer on MDF

wayne

>the MDF I am going to use is 1/4" and I was planning to do both sides as when you open the doors the panels will be visible. What blade do you use when resawing.

Re: wood vaneer on MDF

#8

Re: How about curved section MDF and veneer?

Mark McC

>To get 4 ....3.5" wide x 5/8" thick laminated curved sections out of solid wood, I need to build the jig(likely only one), re saw all the wood into 1/8" thick strips x 4, glue them up one section at a time, clamp to the jig, let it dry, repeat for three more.

Using MDF, I was thinking about gluing up one long 4-5" thick x 3.5" high section made of several MDF strips.

Then bandsaw 4 curved sections out of that long thick strip, and then laminate one strip of solid wood veneer onto each curved section.

Feels easier , except for sanding and making sure each cut section is the same radius, but maybe its not the best way.

M

Re: wood vaneer on MDF

#9

Re: wood vaneer on MDF

Doug in Denver

>I usually use exotic veneers I buy - like bubinga - so I have never resawn my own.

Re: wood vaneer on MDF

#10

Re: How about curved section MDF and veneer?

Doug in Denver

>I see what you are saying. Not bending the MDF, but treating it as though it were a huge block of solid wood. I would not do that I don't think. Not only is mdf messy as heck to work with, but cutting through the factory surface along the whole face of your curved pieces will give you a really fuzzy/rough surface that will be hard to get smooth, and it will want to soak up glue.