Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Today's Deep Thought

Posts

Today's Deep Thought

#1

Today's Deep Thought

Thomas Skaggs, Foothills of Mount Level

>At lunch today I was getting ready to eat a hot dog. But then I realized I only was hungry enough to eat half of it. So I decided to cut it in half with my Unisaw. Worked well. Good thing I don't have a Saw Stop...that would have been an expensive mistake. ;-)

Tommy

Re: Today's Deep Thought

#2

Re: Today's Deep Thought

Ernie Miller

>You are suposed to use a band saw for that type of operation smaller curf that leaves more for you afternoon snack. Would a saw stop even work if the hotdag was in a bun? would there be enough gonductivity for the electronics to work? is there enough contunity in a hot dog bun? Time for a test? where is the next wood show?

Re: Today's Deep Thought

#3

Re: Today's Deep Thought

Jesse in New Mexico

>Tommy,

You need to spend more time in the handtools forum ;^)

Re: Today's Deep Thought

#4

JL

Re: That's what "chop" saws are for :)

JL

>

Re: Today's Deep Thought

#5

That is Cutting the Mustard!

George@Colonel's Workshop-Havertown PA

>Tommy,

Consider using the band saw with fence, and slab off hot dawg slabs. Some like quarter sawn hot dogs better--to save face.

George

Re: Today's Deep Thought

#6

Re: Today's Deep Thought

Dave Anderson Chester, NH

>I think I know someone on this forum with too much time on his hands. Not that I'm gonna name any names mind you. Don't you have ssome serious design work that needs to be done on the back of an envelope or napkin? Quit loafin' and back to work.

Re: Today's Deep Thought

#7

I thought they were only to be consumed in 3's???

Mike in Paradise

>

Re: Today's Deep Thought

#8

My favorite...

HC Sakman

>When you drop your keys in hot lava; Forget it man, they're gone.

By Jack Handey

Chico...

Re: Today's Deep Thought

#9

Bookmatched hot dog veneers

Dale in Alabama

>... attached to twinkie substrate.

Re: Today's Deep Thought

#10

JL

Re: LOL

JL

>

Re: Today's Deep Thought

#11

Why Wouldn't You Use A

Howard In Toronto

>Dremel tool and cutoff wheel?

Shhheessshhhh......

Re: Today's Deep Thought

#12

Sawzall would have been moe appropriate!

HC Sakman

>

Re: Today's Deep Thought

#13

Re: Today's Deep Thought

Bill Sands

>Not to worry Tom. You can cut up your hotdog on the SawStop in bypass mode. A feature added for that very reason and to also cut non-ferrous metals. Be sure to use a push stick if you cut it in half longways.

Bill

Re: Today's Deep Thought

#14

JUST THINK OF THE POSSIBBITIES IF

Ken Oakley-Sunny St. Cloud, Fla.

>IT HAD BEEN A HEBREW NATIONAL KOSHER ONE. MIGHT HAVE A LOT OF RABBI'S HEADING FOR THE UNEMPLOYMENT LINE

Re: Today's Deep Thought

#15

Thanks for the tip!

James Dillon in MD

>I've always used a tile cutter (kosher of coarse) to cut my Nathans hot dogs. They get a little soggy, but a few minutes in front of my wifes hair dryer brings them back to life. Add some mustard and onions and they are good to go. Think I'll fix one right now 8-).

Jim

Re: Today's Deep Thought

#16

Re: Thanks for the tip!

Miles

>Pix to follow but I did amusing neander things to a very dry Polish sausage recently - sliced off a couple of hundred 0.3 mm slices with a jack plane and a shooting board. It was too hard to cut any other way. The feathery slices were rather nice to eat and I made SWMBO very happy to have saved this delicacy.

I haven't cashed in the brownie points yet... but I might need another plane blade soon ;-)

Miles