Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Alaskan Mill question?

Posts

Alaskan Mill question?

#1

Alaskan Mill question?

Barry Irby

>I have my eye on a huge burl. It has to be six feet by eight feet by about four feet.

Wondering about an Alaskan Mill to saw it up. Several people here have posted pictures of wood they cut up.

I have a Stihl chainsaw with a 20 inch bar. I think its a 390MS, but its too early to go look.

Can somebody clue me in. Is this a big enough saw? Would a longer bar be necessary? Is there anything special about the bar? Are ripping chains commonly available?

What kind of money gets into this? Accessories, etc.

And, Isn't running one of these a huge amount of WORK? Seems to me that just dragging the saw through the wood would take a lot of effort.

Re: Alaskan Mill question?

#2

Re: Alaskan Mill question?

Keith Newton

>Before anyone answers this, could you give a little more information.

What kind of tree is this, and how do you plan to use the wood? Have you ever harvested a burl before?

Can you post a photo?

Have you inquired about ownership, and cost?

Re: Alaskan Mill question?

#3

Re: Alaskan Mill question?

Barry Irby

>It�s an Oak Burl, don't know which species of oak, but pretty sure its Oak. The tree itself is probably 26 to 30 inches below the burl and it is about three feet off the ground, wrapped completely around the log and between double and triple the size of the "Stem". The burl is relatively smooth as they go. It almost looks like someone took dough and wrapped the tree and applied bark, if that makes any sense. Don't have a picture. Not posting the GPS coordinates either :).

I have harvested a number of smaller burls, some more than eighteen inches in diameter, but nothing like this. You would need a crane to lift this one.

I would like to get some table top type slabs out of this and some turning blanks. Not firm on that until I open it and see what I have.

And yes, I know who owns it and he wants a turning lesson in return for the burl.

Re: Alaskan Mill question?

#4

Re: Alaskan Mill question?

Mark Mandell - Gone Round In Jersey

>Believe you're out of your . . . . league, Barry. Especially far out of your saw's league!

Slabbing out that large of a piece will take a real sawmill, I think. You'd be better served to make a deal with a commercial band mill in your area, truck it to them, and watch the fun as they slice it up. You'll save money in the end.

|;-}}

Re: Alaskan Mill question?

#5

I have an alaskan mill

Mike in Paradise

>The 390 is a plastic CrankCase saw not really designed for milling.

Go over to Arboristsite and look for the first post from a user name CoverInSap and see his bad experiences with the MS390 and milling...(Plus he ends up in a big fight with the site and gets banned after a few months, off topic but entertaining)

http://www.arboristsite.com/showthread.php?t=31315

With an Alaskan mill you will lose about 4 inches off of the bar size of your chain saw with the area that attaches the mill to the saw. Eg 36" bar = 32 inch cut max. Your 20 inch bar will only give you a 16 inch cut.

There is nothing special about the milling bars. The ripping chain will give you a smoother cut but I have milled with a regular chain with no problem when I have forgotten to bring a ripping chain with me (The wood in the picture was done with a standard chain).

You can get the ripping chain from Baileys-online for about 23 cents a link.

You also need something to start the first cut on and I use my aluminum ladder for that.


You did not say what you want to do with the burl wood and what size of pieces you would like to keep or how hard the wood is.

Your MS390 will struggle with a really large bar required to tackle that size of burl if you are going for larger width pieces.

I have a Stihl MS660 that I use in my Alaskan Mill and I would not want to use a saw much smaller for other than occasional use.

Milling is very hard on a chainsaw as you are running them wide open for a much longer time than they usually run.

Milling is very hard on you as well as it is physically demanding hard dirty work that is also very satisfying.


img

Re: Alaskan Mill question?

#6

Re: Alaskan Mill question?

Mike in Paradise

>Answers as I was typing...

"I would like to get some table top type slabs out of this and some turning blanks. Not firm on that until I open it and see what I have."

You would need a 48" Alaskan mill with a very big bar which would require a very big saw.

Re: Alaskan Mill question?

#7

Re: PS

Mark Mandell - Gone Round In Jersey

>Google lists a number of commercial mills in your area, but I couldn't see if they were band or rotary mills.

mm

Re: Alaskan Mill question?

#8

Thanks, I think I have too many too's.....

Barry Irby

>My saw is too small,

I'm too old,

Too little

and too lazy....

I don't own a Alaskan Mill and am too cheap to invest in a really big one. I think I'll hire this done and stay out of the way so I don't end up too Dead.

Re: Alaskan Mill question?

#9

Re: Thanks, I think I have too many too's.....

Keith Newton

>Before you dig yourself a deep hole, or give up on it. You can get a pretty good idea of what the wood looks like by knocking a little of the bark off by striking it at an angle with a hammer. A lot of oaks just seem to have just a big swirl without having very interesting graining.

Even if you find someone to saw you some nice big interesting slabs out of it, you will be faced with a pretty good task of drying it properly without it self-destructing, or warping into something that you can't use.

If you do cut it, be careful not to cut the trunk too close up under and over it. There is usually some pretty nice figured wood there.

Re: Alaskan Mill question?

#10

Ellis Walentine

Big expense, much work

Ellis Walentine

>Back in the '70s, a friend of a friend named Bob Sperber "invented" his own brand of Alaskan mill. Granberg's lawyers eventually got him on infringement, but not before Bob had made and sold quite a few of these things. To make a long story short, I had a 40" DBH curly hard maple on an inaccessible hillside and the only way it was ever going to get to a sawmill was if I hired a helicopter or a Caterpillar. Bob brought one of his bigger mills -- I think it was 46" bar, maybe 54", with two 090 AVs on it, one at each end. There were four of us, plus countless jugs of gas, replacement chains, earmuffs -- you get the picture. Anyhow, we milled about a thousand feet of 8/4 from that log in an afternoon. My B&W photo of the mill in action eventually became the cover picture on Bob's first catalog. Without the second engine, we couldn't have done it at all. Bob later made up another long bar and slabbed up a 9'-diameter bubinga log for Monteath in central New Jersey. Again, dual engines were the key.

The moral of the story is that it's a lot of work and expense for one burl, especially if you can get it hauled to a big vertical band mill. A Woodmizer or other small portable mill won't be able to get out full-width slabs. What would you do with 4' x 6' slabs anyhow? That's Nakashima Peace Table territory.

Ellis