Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Unisaw bearing replacement

Posts

Unisaw bearing replacement

#1

Unisaw bearing replacement

Paul Blackwell

>My new bearings arrived the other day, and I read the article by Bill Tindall detailing step by step how to replace them. He said he put the arbor in the freezer for a couple of hours, and heated the bearing to 100 degrees. I can see that freezing the arbor would cause it to shrink, but I'm having trouble getting my mind around heating the bearing to make the bearing hole larger. It doesn't seem to me that the expansion is unidirectional (outward). Wouldn't expansion of the metal cause the OD to increase and the ID (hole) to become smaller? At any rate, I tried following the directions, froze the arbor and tried gently slipping the bearing onto the threaded end of the arbor. As soon as the bearing slipped past the threads, it became wedged so tight I'll have to press it off the arbor. It seems to me that freezing the bearing would cause the hole to become larger. Any suggestions greatly appreciated.

Re: Unisaw bearing replacement

#2

Re: Bill Tindal is correct

Larry Clinton At Frankfort (Central)., Indiana

>Freezing a bearing will cause the ID to become smaller. Heating it will cause the ID to increase. If you have the bearing part way on, I would take it to a local machine shop in your area. They have the equipment to press the bearing on without farther ado. Some automotive (NAPA type) supply houses also have the equipment and expertise to do this if you don't have a machine shop locally. If you elect to remove the bearing DO NOT pull from the outer race as you will damage the bearing. Pulling and seating (pressing on the bearing with force) must be done by pushing / pulling on the inner race only. There are split pullers designed for this job. These may be purchased at the same shops mentioned above.

Re: Unisaw bearing replacement

#3

Imagine this...

John in New Mexico

>if the inner circumference of the bearing were made up of a ring of dots (say individual atoms). Heating causes the material to expand, thus there is more space between each individual dot though the number of dots does not change. More space between them translates to a larger overall circumference, and thus the bearing gets bigger.

John

Re: Unisaw bearing replacement

#4

Re: Bill Tindall (sorry Bill) is correct

Larry Clinton At Frankfort (Central)., Indiana

>I fat fingered the keyboard again. I reread my typing before posting but somehow it is easy for me to miss a name letter missing.

Re: Unisaw bearing replacement

#5

Another Image.......

Barry Irby

>Instead of looking at the bearing as if it were a bunch of parts, imagine what would happen if it were a solid piece of steel. This solid piece does not even have the hole in the middle. If you heat it, all the steel expands and gets bigger. So, if while it was cold, you drilled a hole in it. Then when you heat it, what would happen? All the steel around the hole would expand, just as before and therefore the hole would get larger along with it. The hole would expand about as much as the steel you drilled away would have.

Re: Unisaw bearing replacement

#6

Jesper, Denmark

Re: Unisaw bearing replacement

Jesper, Denmark

>Look in the BP articles section.

No need to freeze or heat, drive the bearings onto the shaft with a copper pipe.

Re: Unisaw bearing replacement

#7

Re: Unisaw bearing replacement

Chuck Lenz

>I'm not sure that heating the the bearing up that much would be a good idea. What does it do to the grease inside ?

Re: Unisaw bearing replacement

#8

Or howzabout...

John in New Mexico

>if you cut the bearing ring an straighten it into a strip (yeah, nothing to it!). If you heat it up the strip gets longer.

John

Re: Unisaw bearing replacement

#9

Re: Unisaw bearing replacement

Larry Clinton At Frankfort (Central)., Indiana

>Chuck, Bill Tindall recommended heating the bearing to 100 degrees. This is actually far below the normal operating temperature of bearings. I worked in an Electric motor repair center for a couple years in my youth. (later retired after 39 years as a Manufacturing Engineer). Many motors run at and above a 50 deg C rise above ambient temperature. This is about 95 F above the surrounding air - which may be in many locations above 100 degrees. I would have no reservations about heating any normal bearing to twice Bill's recommendation or 200 degrees. However, I would not normally even heat a bearing to put on a saw arbor. I have a 1 ton Dake arbor press. I would use a pipe or other round spacer that bears only on the inner race and seat the bearing. As Paul did not appear to have much experience replacing bearings, I recommended he have a local experienced shop seat them. In my area they would do it for free, or at most $5 or less. Several shops in my small city have presses and the proper size spacers / pipe to do the job without damage to the arbor or bearing. They will (as would I) also ensure the arbor is supported properly to ensure it is not bent or damaged on the end opposite the bearing when they seat the bearing. Rather than go into a long explanation of the proper method of doing this, I believe it may be in his best interest to have it done. If it was a job he had to do repeatedly, it might be better to obtain the proper tools and experience, but this is probably the last time he will ever need the knowledge.

Re: Unisaw bearing replacement

#10

Sage advice indeed

bill tindal, E.TN

>Funny, I had this same argument with a machinist. Although he knew bearings operated at much higher temperature than I heated it to, he still insisted that heating the bearing was a very bad idea. What ever. Certainly if one has a press and knows how to use, it that is the way to go. And lacking that, find someone that does. If it was not a 40 mile trip to town I would have paid someone to press my bearings on, but out in the sticks one gets in the habit of seeing what one can do with waht one has at hand.

Re: Unisaw bearing replacement

#11

In my former Job...

Gary Camp, Bend, Oregon

>As a skilift mechanic, we heated gearbox bearings to 325 - 350 deg F, of course these bearing were oil lubricated. A bucket of 90wt, a rosebud torch and a candy thermometer. When you pulled the bearing out of the oil you wanted to be quick about getting it on and seated. The thoughts of having a 6" id bearing cool half way on the shaft were pretty scary. Our gearbox guy had an old french fryer in his shop, plop the bearing in and set the temp. Another option, hang the bearing over a 100w light bulb and put a foil tent over it, monitor the temp

glc

Re: Unisaw bearing replacement

#12

Re: Unisaw bearing replacement

Chuck Lenz

>Sorry, I didn't realize it was that low of a temperature.