Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Veneering Face Frame?

Posts

Veneering Face Frame?

#1

Veneering Face Frame?

Craig in NJ

>Hello all,

I am going to veneer the face frames of my old kitchen cabinets (which now hang in my workshop). I plan to veneer the inside of the face frame with 13/16" veneer (this is the side perpendicular to the front of the face frame). I plan to veneer the front of the face frame with 2" veneer. So the two edges will meet at a 90 degree angle. My question is, what surface do I veneer first?

Thanks for any suggestions!

Re: Veneering Face Frame?

#2

I'd probably do the inner one first

Don Henthorn

>and the outer surface second. That way the outer surface would overlap the inner and there would also be a wider face to use a small router to trim the veneer flush if you wished to use a small router. For a shop does it really make that much difference? Just curious.

Re: Veneering Face Frame?

#3

Opposite opinion

Rob Sandow

>Dong the sides first and then the fronts will present an uninterrupted look to the front of the cabinet, which is desirable. However, that also leaves the front with an edge that may be vulnerable to catching on items being removed from the cabinet and possible delamination. If you do the front first then the sides, there will be no possibility of this, and the veneer job may just last longer.

Rob

Re: Veneering Face Frame?

#4

Re: I'd probably do the inner one first

Craig in NJ

>Don,

Thanks for the response. This is a learning experience for me. I always want the things I build to be the best I can make them. So I am trying to get this to come out looking the best as I might do this to other cabinets sometime down the road. Thanks again!

Craig

Re: Veneering Face Frame?

#5

Ellis Walentine

How are you going to glue the veneer on?

Ellis Walentine

>This seems like an inordinate amount of work for a possibly questionable outcome. You could practically replace all the face frames with solid wood in less time than it would take you to veneer the old ones. Plus, unless you're thinking of using contact cement (I hope not), you're going to have to do a lot of sanding or scraping or paint removing first to prepare a veneerable surface.

I would save the veneering exercise for something else and replace the existing frames with new ones instead.

Ellis Walentine, Host

Re: Veneering Face Frame?

#6

What is 2" veneer?

Doug in Denver

>Since nobody else has asked, I am obviously the dummy here, but what is 2" veneer? Or 13/16" veneer for that matter? You can't be talking thickness. You mean width? If so, what is the veneer you are using? How thick?

Re: Veneering Face Frame?

#7

Re: Veneering Face Frame?

Jerry Samsen

>I have refaced cabinetry with the peel and stick veneer available from a number of sources (Rockler comes to mind). The veneer is thin enough to fold right over the face frame. The sides of the cabinet (if any exposed) should be faced with 1/4" matching hardwood ply first so that you cover the edge of the ply with the veneer. Use a water based contact cement -- don't rely on the adhesive alone in the peel and stick.

Just curious why you would go to this trouble for cabinets in the garage?

Re: Veneering Face Frame?

#8

Re: Veneering Face Frame? *LINK*

Jack Lane

>Craig,

I run a cabinet shop and one of the services we offer is cabinet refacing. The product we use to cover the frames is called Wood-over-Wood. It's two ply with the select species over a layer of luan(like real thin plywood). We use StarStuk spray contact cement to attach it to the frames. That's a pricey set-up so I'd recommend using regular aerosol spray contact cement (like 3M) to stick it. Just use a piece of laminate or a board to keep it from getting all over everything as you spray. Also, don't try to roll this stuff out with a J-roller. You can't get enough pressure on it. Use a piece of plywood or masonite like a scraper only cover it with a piece of cloth. Put a lot of pressure on it to make sure you get a good bond. You can also use ice scrapers if you have them available.

We finish the full sheets of WOW in the shop and use a hand held Virutex laminate slitter to cut it. A straigh edge and sharp razor knife works well too. We cover the inside and outside edges of the rails/stiles first and cover the front of the frames last. You would use nearly the same procedure you would use if you were covering an item with high pressure laminate. I always assmemble the pieces of WOW on the front of the frame the same way the orginal rails and stiles were assembled. At vertical joints I cut the piece a little long, glue it, and cut using a combination square as a guide.

Trim everyting you can with a NEW flush trim bit.

This system works better than any other method I've seen. The peel and stick stuff is easy to screw up and get bubbles under and the phenolic backed leaves black lines in places you don't want them. We buy our WOW from Keystone Wood Specialties. Good luck

Jack


Keystone