Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Delta Drill Press

Posts

Delta Drill Press

#1

Delta Drill Press

David Hammond

>I'm looking at the "DELTA DP300L 12" TwinLaser Crosshair Drill Press" from Lowes for my shop. My main use for now will be drilling high end pen blanks. Anybody have this press and some experience with it? I'll be using a centering vise on the table - when you raise and lower the table on the press, does anybody know if the table moves in any other direction that up and down? I've got an old drill press, and when you loosen the table to move it up or down, it also moves left to right, losing my adjustment to center.

Also: I've gotten some advice already about the drill doctor. I'm looking at ordering the "Drill Doctor 750X 3/32-Inch to 3/4-Inch Drill Automatic Bit Sharpener" from Amazon. I've read some great reviews, and a few negative ones. I would like to sharpen normal twist bits, and I just got a Dewalt set of drill bits that will be dull eventually, that I would like to sharpen. Any advice, or whatever is much appreciated!

David

Re: Delta Drill Press

#2

Re: Delta Drill Press

john lucas

>David I don't know about that drill press but if the lazers are accurate all you have to do is get one of the crossfeed drill press vises and realign it with the lazer after you move the table. At least that sounds like it might work.

What I did for my old Delta drill press was to drill 1/8" holes in the bottom of the rack gear teeth and install 1/8" roll pins. I put them in 3 different places. This pretty much locks the table from moving left and right. There is a little slop however so it isn't perfect. You could probably put some set screws and a brass bar in the space and take up all the slop. I'll look when I go out to the shop and see. If I ever need to move the table top sideways I just knock the roll pins out. They fall through the column to the floor and it's pretty easy to tilt the drill press and grab them with a magnet to reinstall them.

I haven't been super impressed with the drill doctor. It does OK on larger bits but leaves an odd shaped point on smaller bits. It may do OK on 7mm bits or around that size. Things like 3/16 on down I just toss and buy a new bit. I don't think the drill doctor did a good enough job. fIn fact I sharpen these by hand better than it does. The main reason Ibought the drill doctor was after several hand sharpenings I started to get the point off center. The cheapest drill doctor is a piece of junk. The ones with the diamond cutting tool are pretty good.

Re: Delta Drill Press

#3

Re: Delta Drill Press

Jonathan

>I just bought a 10" drill press from Delta, and I also would like to drill pen blanks. Unfortunately, the press does not allow the full blank to be drilled in one shot, which means that the table has to be moved in the course of drilling a single blank.

I am considering returning the drill press (if I can - it has been less than 30 days, though it has been used) and getting another one, but is there a drill press out there that allows you to move the table up and down without moving side to side? My two attempts thus far have been straight holes that are off center because of the movement of the table once the center was found using a pen vise.

Any help is appreciated. I am not very handy, and am a bit frustrated.

Thanks,

Jonathan

Re: Delta Drill Press

#4

You really need a press with more quill travel.

Don Henthorn

>

Re: Delta Drill Press

#5

Re: Delta Drill Press

Tom MacGregor

>A press with more travel is the best answer to your problem or it will be a pain every time you do that operation forever. I might even suck up a "restocking fee" or whatever to get what I really wanted. Spread out over the life of the machine you're talking pennies a day or less. If you end up stuck with what you have now you might be able to use a drillpress vise or make some kind of jig to flip the blank over end for end instead of moving the table.

Re: Delta Drill Press

#6

Re: Delta Drill Press

Ted Owen, Pittsburgh

>Jonathan, with some species I have better luck drilling from each end, then cutting off the pieces for upper and lower pen barrel. Ebony works only that way.

Best, Ted