Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Durable finishes

Posts

Durable finishes

#1

Durable finishes

Adam Baum

All,

I have been using General Finishes Woodturners Finish for awhile now. My method of application is about as simple as it gets: dunk the item in the finish, drain the excess, put it back on the lathe at 55rpm for 10 minutes to prevent drips/pooling, repeat enough time until it's where I want it to be.

My problem is that GF no longer sells this particular finish in larger sizes. Larger sizes weren't selling well so they got rid of them.

Are there any other finishes out there that I can use the same application method and is also sold in larger sizes (half gallon or gallon)?

Re: Durable finishes

#2

Re: Durable finishes

Dick Coers

Surely one of the several other General Finishes water based finishes would be comparable. Ask them.

Re: Durable finishes

#3

Re: Durable finishes

Roger Chandler

I have used a good bit of the Woodturners finish from GF........even did one demo for a club on it last year.

That finish has extra driers in it, which makes it so fast drying. The way I finish with it is to finish on the lathe [old towel underneath on the ways to catch any drips] and use a square of t-shirt material and spin the piece at about 80-100 rpm's and just it overlap itself a little with each rotation. I have had good success with this method.

I have also found that as I get about 2/3rds way down toward the bottom of the can, that the driers evaporate with an open can over time, and it affects the process I use a little....not much, but I can tell the difference in a new can and one that has been opened for numerous projects, so I always purchase the quart size can.

In a hot shop, this finish will dry too fast using my method on a large project, and will get some streaks in the finish. My shop is not air conditioned and gets over 90 degrees in the hot summer.

Re: Durable finishes

#4

Extra driers? In water based?

Dick Coers

I don't think think that is the proper terminology is it?

Re: Durable finishes

#5

Re: Extra driers? In water based?

Roger Chandler

Dick, I am not sure what the technical terms are for this, but I was told by someone back a couple of years ago or so, that the Woodturners Finish had driers in it......what they are, I do not know.

I vaguely remember a thread back then where there was a discussion on this finish and someone said the forumula was proprietary and GF did not release that information.........whether or not that is the case, I have no idea, but someone posted something to that effect.

Re: Durable finishes

#6

Looks Nasty *LINK*

Mark Mandell - Gone Round In New Jersey

Pulled the MSDS on the product. With the glaring notes on chemical burns and serious eye damage potential, I rather doubt I'd even have it in my shop. Given the disclosed risks, not too surprised if they're phasing it out.


https://generalfinishes.com/sites/default/files/file_downloads/sds-wood-turners-finish-general_finishes-ghs-us-hcs2012-v4.3.2-2014.pdf

Re: Durable finishes

#7

Brad Vietje

Could Be ... Alcohol (?)


Re: Durable finishes

#8

Wow, reading all that stuff makes it ........

JamieDonaldson

...sound like the Woodturners Finish is radioactive! I've used it occasionally with not a hint of any such dangers, other than it does dry too fast for most larger surface applications. And like most H2O based finishes it raises wood grain, requiring sanding between coats, but dries to a nice hard finish. My usual go-to finish for light colored woods is lacquer, much nastier than WTF if you read the warnings, and on darker woods I often use Min Wax Wiping Poly.

Re: Durable finishes

#9

Jesper, Denmark

Re: Looks Nasty

Jesper, Denmark

It's a good "Heads up" example or warning that the so-called water based finishes do contain co-solvents that are or can be just as dangerous to the user as the solvents in the older finishes.

Glycol ethers or glycol ether acetates are typically used in waterborne formulations as co-solvents to enable the water to dissolve the oil based resins. Some of them are known to be nasty and others have not been used long enough to have demonstrated how bad they are.

My take is to avoid the devil you do not know and use the old devil you do know. The commonly used hydrocarbon solvents' hazards of flammability and health effects are well known, but can be safely dealt with - even in a hobby shop.