Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Non-turning project I should have done years ago!

Posts

Non-turning project I should have done years ago!

#1

Steven Antonucci

Non-turning project I should have done years ago!

steven antonucci

I have a Craftsman "3HP" Contractor style tablesaw for years now, and I have always hated having to use it for one reason- the 6 foot powercord that it came with! Even worse, it's on the front of the saw and that means I have to have it about 2 feet from an outlet to use it without an extension cord.

The other day I was in the shop, and I took the switch off to see what I would need to make a longer cord. As it turns out, I just needed to buy a heavy duty extension cord, cut the head off, and solder it on to the old tabs. I bought a 15' cord for $10 and I am now able to wheel it into the middle of the floor and plug it into ANY outlet in my shop.

It was about 20 minutes worth of work because of the soldering. Worth every second...

Steve

Re: Non-turning project I should have done years ago!

#2

First, You must perceive the need.....

Barry Irby

Perceiving the need is the genesis of most improvements and inventions. Can't imagine how many times I have made similar small improvements and then wondered what took me so long. I had a weird moment last summer. I was working on a house for my cousin and the plug on my Skilsaw crapped out. At almost the exact moment I figured out I needed to put a new plug on the saw, she asked me is I would help her install a pump on her pool. Sure. So, we installed the pump and as part of the process, cut the cord off it and hard wired it. I asked if I could have the cord and not only did she give it to me, She gave me some heat shrink tubing to use for adding it to the saw. So now the saw has a much longer cord. A strange little piece of serendipity. (Its a great old saw, but factory cords are no longer available)

Re: Non-turning project I should have done years ago!

#3

Re: First, You must perceive the need.....

john lucas

I have tons of perceived needs in my shop. I just don't have the time to do them. One thing I've been putting off is completely redoing the lathe and bench side of my shop. It is in serious need of redesigning. I know it's going to take at least a week to do since I need to rip off the walls and install insulation in that side of the shop.

Re: Non-turning project I should have done years ago!

#4

Why not just use the Ext.cord?

Mike Brazeau

I have a bunch of 14 G ext. cords. Never buy anything less.

Re: Non-turning project I should have done years ago!

#5

Steven Antonucci

Two steps instead of one

steven antonucci

For me, it was about process improvement. Sounds silly, but every time I needed to make a cut, I needed to wheel the saw out close enough to power, find a 14G cord that was 'too long' (since I bought long ones for yard work, not the shop), plug it in, rewind or recoil it...

Now, I just pull the saw out a few feet, and plug it in. I figure over the long haul, I have probably saved myself a few hours worth of aggrevation. Now, if I put better wheels on the saw...

Re: Non-turning project I should have done years ago!

#6

Re: First, You must perceive the need.....

Matt Overton

You mean that I'm not the only one? It seems that any "little" improvement in the shop involves three or four other little improvements just to get the first done. I just had an out of work electrician consolidate all of the minor improvements that I have made over the last 25 years. I think now I can do those other twenty or so projects to make that perfect shop, so that I don't have any excuses anymore for being inefficient!

Re: Non-turning project I should have done years ago!

#7

Leo Cuellar

Re: Two steps instead of one

Leo Cuellar

The first thing I did with my saw was put a 20' ten gauge cord on it and switch it to 220v. The cord is better quality than the wiring in any of the places I've lived. The 220v keeps people from asking to borrow it :D Wheels, wheels, wheels on everything but my lathe so far, makes life in a small shop so much better.