Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Hat #4

Posts

Hat #4

#1

Steven Antonucci

Hat #4

steven antonucci


Hat #4 (#3 still needs finish work). Finished at 6.4 ozs before oiling, made for my daughter. #3 was 7.5 oz, so it's a little bit too thick. #4 (this one) is the epitome of check and measure everything, as there is a chainsaw cut in the bottom than never got turned away (duh!). When you only have 1/16" of wood, you can't fix stuff like this. There are also two small holes in the hat band from a careless microsecond with the bowl gouge, but those can be patched with epoxy.

I will try at least one more to get all of the elements right...

Steve

P.S. Cell phone pic -sorry

Re: Hat #4

#3

Steven Antonucci

Details make the hat (#3 pic)

steven antonucci

I took a (crappy) cell phone picture (now that it connects via Bluetooth to my laptop!) of hat #3.

I like the indentation in the top of #3(left), but I like the smaller taper on #4 (right). It's amazing that there is only a 1 oz difference in these two hats, as #3 is 7.5 oz and #4 is 6.4 oz (before oiling). I am planning on burning the band on #3 with my woodburning pen.

#5 will get the thinness and upper crown of #4, but the 'rolled bead edge, wider band, and recessed top of #3. My goal is to make one that I can actually wear (neither of these fit me, dangit!) Perhaps this weekend...

Steve

Re: Hat #4

#4

Mike Stafford

Re: Details make the hat (#3 pic)

Mike Stafford

Steve, I will agree with you about your photo quality but I think you have done a fabulous job on hats #3 and #4.

I think you will only get better as you continue turning them. I would be proud as all get out if I had turned either one. (By the way proud as all get out is Southern for you done good, son!)

Re: Hat #4

#5

Re: Hat #4 My question(s)

Mike Jones in Redding, Ca.

Steve, do I understand that you are turning your hats from dry blanks and then steaming and bending the brims? If so, why? It seems to me to be a much more formidable task than the Johannes way.

Re: Hat #4

#6

Re: Hat #4 My question(s)

Mike Jones in Redding, Ca.

Steve, do I understand that you are turning your hats from dry blanks and then steaming and bending the brims? If so, why? It seems to me to be a much more formidable task than the Johannes way. ??

Re: Hat #4

#7

Steven Antonucci

Thanks Mike

steven antonucci

Some of my favorite expressions come from the south. I am a big fan of "I'll tell you what' and "well, he needed killin'"

I should post a picture of them "lit up" - they might make a very interesting lampshade.

S

Re: Hat #4

#8

Steven Antonucci

negative...

steven antonucci

I turn them just like Hannes does, except for the tops, since I haven't gotten around to making my lightbulb thing. (I'm actually going to make a similar device using an LED flashlight-cheaper and safer I think)

I had asked about steaming them because I wanted to crimp the top and really curl the rim. I don't think I got #3 thin enough to do that, and steaming the brim made it much more flexible, but not so much that I could crimp the top.

#5 will definitely be a compilation of everything I learned in 1-4...if it survives. I will be trying for sub 6 ozs... and I think I know how to do it.

Stay tuned

S

Re: Hat #4

#9

steve a question...

ihmserv

why are you trying for less than 6 oz ?

I have made a couple of hats in the 8 to 10 oz range. and have had no problems.

as a comparision I wear leather western and stetson hats most of the year, so I a colection of them (6 actually) they all weigh in at between 12 to 14 oz.

my felt and canvas hats that I wear in the summer, weigh in at 5 to 8 oz.

hope you are having fun with these I know I do.

one more point, your led flashlight idea might not work mine didn't the high speed spinning always seemed to screw up the works. the light kept going out at the worst possible time.

but I was only using cheap flashlights.

IAN

Re: Hat #4

#10

Re: steve a question...

cliff

nice work steve , cliff here frequent lurker, ocasional poster, have made a few hats always fun and a challenge too. i use the michelson methods and have had good luck rubbing the band with rosewood. made a small version of the jam chuck with the light makes a world of difference, cut thriugh a few tops before i made one. ihope you will continue to post your progress and what do you use for jam chuck? will try to get a couple of mine on here.

Re: Hat #4

#11

Steven Antonucci

Hmmm...interesting, guys!

steven antonucci

Right not, I am not using a jam chuck. I am putting the hats against a set of cole jaws with the tailstock for support. I can get down to about 1/4" nub and break it off. I clean up the nub with a cabinet scraper.

I want to make the jam chuck, but I was never crazy about having a light bulb inside the hat with a lathe running. I seem to recall seeing what happens when something goes wrong in a demo, and I'd rather not have to deal with it. The small LED flashlight is contained, and I would very little risk if it didn't work. I'm guessing that it will be plenty bright enough over 2-3" distance it would need to illuminate, but I never thought about if it would shut off if spun. Have to try it now...

Steve