Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Thread chasing by hand

Posts

Thread chasing by hand

#1

Steve Kubien

Thread chasing by hand

Steve Kubien

I know there have been a few threads on threads lately (sorry, I couldn't resist!) and I've gotten the bug to give it a try. I've looked at commercial chasers and they always seem to come in pairs. My question is, why?

Couldn't someone make a chaser out of a bolt and use the approach the work from the end of the lathe as though they were hollowing a box or form? Why the need to approach the male threads from the side? Do I need to make two tools and have someone braze a piece of threaded bolt perpendicular to the shaft of another bolt (or similar piece of steel)?

I'm only at the very beginning of this particular journey so I could be missing something really simple.

At this time, a threading jig like the Bonnie Klein or the Baxter is out of the question (financially).

Thanks!

Steve

Re: Thread chasing by hand

#2

Re: Thread chasing by hand

John Lucas

I made one out of a bolt that I cut in half. It does work for boxes although you have to push on the sharp edges of the bolt while turning the male threads which hurts your thumb. It's also hard to pull the bolt toward you while cutting the female threads.

You also can't cut threads on a spindle if you want to.

I made my others out of bolts cut in half but one half is welded with the teeth parallel to the handle and the other is perpendicular to the handle. This is like the commercial tools are made although theirs have teeth cut into the shafts by machine.

Mark St. Leger's tools are made of one piece of steel with a tool on each end. You still have 2 tools but now you can't lose or misplace one of the tools. They are useless without their mate because you do need a male and female version.

Re: Thread chasing by hand

#3

Steve Kubien

Re: Thread chasing by hand

Steve Kubien

I figured I was missing something. Thanks John. Have you got a link to Mark's site?

Re: Thread chasing by hand

#5

Steven Antonucci

Steve- before you buy, don't give up on the bolt!

steven antonucci

I did EXACTLY what you said, and it works very, very well.

I started with a 'regular bolt'. It worked OK. I bought a 'better bolt' (grade8), and it worked better.

Finally, I decided to make my own.

Get a section of good tool steel about 6" long in whatever diameter to fit a die and cut your own threads. I usually thread about 3/4", slowly, and clearing the cut of metal shavings often to make a good, clean thread. Next, I grind a flat on the top, and hone it smooth. The flat should be at the diameter of the rod. Lastly, I ground two angled relief cuts underneath the rod, making sure to not destroy the threads! (completely optional) Viewed on end, my threaded section is an upside down triangle.

To cut the male threads, you use the right side of the chaser. Females cut on the left side. One motion instead of two motions to master. In addition, the threads are perfectly matched because they are from the same rod and only cut with one tool.

Should take you about 30 minutes in a well equipped shop.

S

Re: Thread chasing by hand

#6

Glad you found it.

John Lucas

I had to run out and shoot several photo assignmemts. Mark came and did demo at out club last week so I got to actually hold one of his chasers. I like them a lot. They are good and thick. Very cleanly built and store inside their own handle. That's the tool I would recommend but that's based on my very limited knowledge and use of other tools. I have a set of Sorby, and some factory made antique chasing tools. The rest were all made by me. Making them was interesting but it's like anything else. The professionally made tools really are better.

Re: Thread chasing by hand

#7

Re: Thread chasing by hand

Allen Neighbors

This is my thread chaser. Made by a friend in Australia. If you pm me, I can get you in touch with him. He made several and sold them. He might make some more.

It's from a bolt, or a rod of hardened steel. And like Steve A. says, you only have one movement to master... wax on, wax off... sort of. :D