Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Quick notes on steam bending a hat

Posts

Quick notes on steam bending a hat

#1

Steven Antonucci

Quick notes on steam bending a hat

steven antonucci

It doesn't work!

I think we all know the saying that "a watched pot never boils". I had the idea that I could get a lot more mileage out of the brim of my hat if I had steamed it first. Seemed to take a year to bring the pot to a boil, but only a few seconds to start getting enough movement in the maple to introduce some cracks!

I quickly learned that upside down "inside the pot" was no good because it was steaming unevenly. Right side up on top of the pot also doesn't work because the steam gets trapped inside the hat, which causes it to steam unevenly too. The differential moisture seemed to make one side move way more aggressively than the other, which introduced the crack. I am pretty confident that they will close, but I bet I wouldn't have gotten them at all if I hadn't steamed it.

I weighed the hat last night at 9.6 oz. It was 8.65 oz this AM, and 8 oz after I finished sanding it today. I will probably blow the next one up trying to get it even thinner :) The brim definitely needed to be steamed to be bent as much as it is...

I'm going to let it sit for a couple of days, and I am hopeful that it will oval a bit more than it has, since it doesn't fit me quite right yet. All finish sanding will be done by hand, and I am hoping to be able to wear it to my next club meeting on July 26th.

Pictures soon...

Steve

P.S. Perhaps I will try boiling the next one ;)

Re: Quick notes on steam bending a hat

#2

If it does not elongate enough.....

Barry Irby

Take a ROS With some 320 on it and sand off the front and back of your head a little. It goes faster with 220, but its more painful.

Re: Quick notes on steam bending a hat

#3

Steven Antonucci

I was honing my gouges

steven antonucci

but I think your way will be a little bit better ;) Mine would have been faster, but the scarring would have made up the hat size gains.

S

Re: Quick notes on steam bending a hat

#4

Re: Quick notes on steam bending a hat

Doug Thompson near Cleveland

Knock it down 2 oz's and it will bend.

Re: Quick notes on steam bending a hat

#5

Steven Antonucci

Cut # failure to get some readings

steven antonucci

So I wondered what kind of thickness I had in one that I broke the rim bending.

Bandsawed it in half, and it was pretty obvious why they wouldn't bend.

The rim was between 80-120/1000ths.

Right above the hat band, 55/1000ths

1" above the hat band 80/100ths again

2" above the hat band 120/1000ths (2.5x-yikes!)

right below the top of the hat 180/1000ths (3.5x---AAARRRGH!!!)

The new one will be much more consistent in thickness- probably 80ish throughout, and should dry well under 8 ozs. Sanding to final thickness is cheating, but always an option :)

s

Re: Quick notes on steam bending a hat

#6

Re: Quick notes on steam bending a hat

jim miles - charlotte n c

Been experimenting with gluing green wood and turning a SEGMENTED hat- no luck yet

turn it thin enough to bend and the glue lines don't hold well.

Re: Quick notes on steam bending a hat

#7

Re: Quick notes on steam bending a hat

john lucas

Jim Keep us up to date on your attempts. I'm always interested in segmented failures. There's so much we can learn from that. What type of glue, where the failures at long grain or short grain joints, type of wood etc. Of course if you do succeed we would naturally love to see that.

All this hat talk has got me excited about turning one but I really need to do other things. Still, I have the wood sitting in the yard just have to find the time to give it a try.

Re: Quick notes on steam bending a hat

#8

Re:John, buying a real hat....

JamieDonaldson

...is a whole lot less trouble, and much faster, and better fitting, and......!!! :D

Re: Quick notes on steam bending a hat

#9

Re: Quick notes on steam bending a hat

dick strauss

Steve,

If you aren't doing so already, you might want to try judging your thickness with a very bright light. My friend tells me this is the only way to make sure the hat is a consistent thickness.

Re: Quick notes on steam bending a hat

#10

Steven Antonucci

Thanks, that's what I am doing too!

steven antonucci

Nearest I can tell 'really bright yellow' is about 55/1000ths. Need to make something for the top next, and I have an idea based upon what Johannes does, but mine is easier I think...

Steve