Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Prepping Segment parts Questions

Posts

Prepping Segment parts Questions

#1

Prepping Segment parts Questions

Barry Irby

I'm slightly OT here, because this is not a turning question, but I am asking on the running board because some of you do segments. I am "rescuing" a bunch of pieces of Osage Orange and making a cutting board out of about fifty end grain segments.

The pieces are 2" thick with the end grain vertical. Some are about 3" square but some are less than 1" square. Some are angled and are not square at all. My problem is that they don't fit as well as I would like. I am using a sharp Forrest WWII full thickness blade. Some of the pieces don't have flat surfaces. They are slightly rounded and won't close up with nice tight joints. I suspect that trying to shave them down to size has allowed the blade to roll or warp slightly and round off the cuts.

I do not have a sled or sanding disk.

So, what have I done wrong and how can I correct it. Is this where a sanding disk comes into play? How can I clean up the joints?

Re: Prepping Segment parts Questions

#2

Re: Prepping Segment parts Questions

Carl Barton

Barry,

I do mostly segmented turnings. When doing this type of work it is best to have all the grain going in one direction so when the wood moves it does not come apart. Most segemented turners use a disk sander of some sort. I have a 10" and a 12". This allows one to close up any gaps between mating surfaces. Without a disk sander it is almost impossable to get good tight joints and without tight joints it is bound to fail over time. Hope this helps.

Carl

Re: Prepping Segment parts Questions

#3

Re: Prepping Segment parts Questions

Barry Irby

Thanks Carl.

I guess I will be making a disk sander to fit on my lathe. What grit do you use? Seems it should be sort of coarse to cut quickly but not too much or it would show up in the joints.

Re: Prepping Segment parts Questions

#4

Re: Prepping Segment parts Questions

Nicholas Tuzzolino

Most segmenters use 80 grit. Touched lightly, leaves the wood just fine for glueing. Be sure and sand off any burrs, they will affect the finish lines .DAMHIKT.

Re: Prepping Segment parts Questions

#5

Thanks and one more question

Barry Irby

I am going to make a disk of MDF and attach it to a face plate on my lathe. At Least that's the plan at the moment. What do I use to attach the sand paper to the disk?

Now to figure out a table.

Re: Prepping Segment parts Questions

#6

Use table saw to make sanding disk?

Opelika Edro

Hey Barry, would it be easier to improvise a sanding disk using your table saw? Then you have the table, plenty of room for clamping fences, etc. Just a thought.

Re: Prepping Segment parts Questions

#7

Re: Use table saw to make sanding disk?

Barry Irby

I was thinking about that. Maybe a piece of half Inch baltic birch for the disk? Wonder what I could use as a piece of metal? I was thinking about using an old saw blade, but them fellows still have their "teefs" and just the thought of it scares me.

Re: Prepping Segment parts Questions

#8

Re: Thanks and one more question

Nicholas Tuzzolino

Barry: I have a 12" Grizzly combination monster sander for my segmenting. However, for smoothing bigger things and larger rings, I made a 20' disc for my Powermatic out of MDF. I sealed it with shellac sealer (lacquer sealer, etc. will do the job) and buy PSA (sticky back) discs. Worked like a charm. Make a flat table to set on the ways next to the disc and take your time.

Re: Prepping Segment parts Questions

#9

Re: Use table saw to make sanding disk?

Nicholas Tuzzolino

A table saw is also a great idea. Think 3/4" of dado blades, substitute a piece of MDF.

Re: Prepping Segment parts Questions

#10

OK, Another set of questions?

Barry Irby

Where do I get PSA disks? What do they cost? Do they last?

I have some cloth backed sand paper, I was thinking of that. I am thinking of this as a one shot project. OTOH Once I have it, I may find many uses for it.

Re: Prepping Segment parts Questions

#11

Re: OK, Another set of questions?

Nicholas Tuzzolino

PSA discs can be found a tstores like Rockler and woodworking supply places.; Not sure about the borgs.

If you have cloth backed paper wide enough to cover the disc you make, go for it. Contact cement or spray adhesive.

Re: Prepping Segment parts Questions

#12

Re: OK, Go To Sears and---

Dave (PacNW)

You can buy a ready made 10" sanding disk and all the disks you need At any Sears Hardware Dept. The very idea of using a piece of MDF , 10" diameter and running at 5300 rpm "SCARES THE HELL" out of me!!!

Dave (PacNW)

Re: Prepping Segment parts Questions

#13

Re: Prepping Segment parts Questions

Malcolm Tibbetts

Barry, you'd be wise to avoid using your table saw as a disc sander. The high speed will likely burn or burnish your glue surfaces. Short of an actual disc sander, you'd be better using your lathe - MDF, spray adhesive, 80-grit, and a home-made MDF platform. This is a lot of hassle for just one project. Maybe you should become a "segmenter" :-))

Re: Prepping Segment parts Questions

#14

Re: Prepping Segment parts Questions

Texian

+1 for Malcolm's suggestion of lathe-mounted disc sander. Mine is 15-3/4" dia. 3/4" particle board plus tool post mounted table. Usually sand at about 150-250 rpm, which makes it easy to just lightly touch up surfaces and is easy on the disc. Clean frequently with big crepe eraser.

Re: Prepping Segment parts Questions

#15

Re: Prepping Segment parts Questions

Bill Stehman

Equipment Surplus usually has Jet 10" cast iron faceplates for around $25 and Klingspor has psa disks for $5.

Makes a simple flat heavy duty disk sander for the lathe. They weigh 12 lbs. Goggle Jet 10" faceplate.

Re: Prepping Segment parts Questions

#16

Re: OK, Go To Sears and---

Nicholas Tuzzolino

Dave:

You are absoloutely right. I was thinking of controllable lathe speeds, not the rpm's of a table saw.

Thanks for pointing that out. Yikes!!

Re: Prepping Segment parts Questions

#17

Re: Prepping Segment parts Questions

Carl Barton

Barry,

I use 60 or 80 grit. When I do my segments I cut them a bit oversize, touch lightly and measure to fit the size I need.

Re: Prepping Segment parts Questions

#18

I have old 10" sander for free

Carl Barton

Barry,

If you live anywhere near Virginia Beach, VA you can have my old 10" Rikon disk sander. I have a new 12" Jet now. While the Rikon has been used allot it is still in pretty good shape. It is just taking up space now that I could be using for something else. In fact if Barry does not live close by me anyone who does can come by the house and pick it up. Just drop me an email.

Carl

Re: Prepping Segment parts Questions

#19

Best offer I have had all day!

Barry Irby

I'll Take it!

Send me a private E-mail with your address.

When do you want to make the hand off? I could do it most anytime.

Thanks.

Barry

Re: Prepping Segment parts Questions

#20

Re: Best offer I have had all day!

Carl Barton

Barry,

Send me an email at Bartoncvn73@yahoo.com or call me at 757-572-6731

Carl