Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

2 day class at Peters Valley is a lot of work!

Posts

2 day class at Peters Valley is a lot of work!

#1

Steven Antonucci

2 day class at Peters Valley is a lot of work!

steven antonucci

I couldn't sleep last night (dorms next to the blacksmithing studio, and those guys had the anvils ringing :) ) A hot and sweaty night had me up at 5 AM today looking for coffee, and in the workshop at 6:30AM. Not a lot to do in Layton, NJ on a Sunday AM, so I turned a little before class.

And then I turned a little during class, while my four student turned non-stop. I walked around all afternoon, and by the end of the day, had adjusted enough tools and stances to have everyone cutting pretty darn well!

Got home to run the bathtub, and a nice soak/snooze.

If you are ever in the neighboorhood, check out Peters Valley. Great facility, good food, and a bunch of great people keeping craft alive.

S

Re: 2 day class at Peters Valley is a lot of work!

#2

Re: 2 day class at Peters Valley is a lot of work!

Jennifer Indy.USA

Your room was next to the blacksmithing studio? Well I hope mine isn't! If my class even goes. I still don't know the status. I'm assuming I'll find out this week.

Glad yours went well.

Jen

Re: 2 day class at Peters Valley is a lot of work!

#3

Steven Antonucci

Lights out at 11PM

steven antonucci

There are dorms in the old buildings throughout the old town of Bevans. Mine was in an old house (Valleybrook), which just happened to be over by the Blacksmith studio.

A lot of non-smiths were interested in what they were doing, so there were a dozen and a half folks milling about the forge. They decided to smelt iron into high carbon steel to have the billet available for making damascus later this summer at a "hammer in" (think Indyfest with anvils instead of the lathe)

As they were fond of telling me "Beer makes better forging".

S

Re: 2 day class at Peters Valley is a lot of work!

#4

Steve Kubien

Re: 2 day class at Peters Valley is a lot of work!

Steve Kubien

Geez, depending on the hour of the day I might have to introduce the 'smiths to the wonderous tones of a Stihl MS390 as it applies to woodturning. Still, it sounds like a good time.

Re: 2 day class at Peters Valley is a lot of work!

#5

Re: 2 day class at Peters Valley is a lot of work!

Matt Overton

Sounds like it went well. Would you do anything different? I know you put a lot of effort into this one. Congratulations.

Re: 2 day class at Peters Valley is a lot of work!

#6

Steven Antonucci

I will reorder one topic, but that's it...

steven antonucci

We started out turning 'sticks'. From sticks, we made beads and coves in those sticks. Then, I moved to faceplate work, illustrated by turning a bowl...

The next day, we repeated it (in an hour). From there, I moved them to turning thin sticks. I had two new turners, and two begining turners cutting trebleurs with spindle roughing gouges. Most were able to get to about 1/8"-1/4" before they'd snap them, but it taught them how to control the tools an gave them the confidence to push their own abilities. It also got them off of 'making a bowl' and into 'failure with learning' mode.

So, when I teach the class again in September, I will move it up to the space after beads and coves.

Sneaked a peek at the evaluation forms too, and all high marks (highest possible). Only "negative comment" was that we should have turned on the air conditioner sooner yesterday (to which I completely agree!)

Thanks for asking.

Steve

Re: 2 day class at Peters Valley is a lot of work!

#7

Steven Antonucci

yeah, the Oneway's don't make enough noise

steven antonucci

plus I'd need a long extension cord!