Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Way To Get Past Artist or Craftsperson

Posts

Way To Get Past Artist or Craftsperson

#1

Way To Get Past Artist or Craftsperson

charlie belden

Thumbing through Ellsworth's book "Ellsworth On Woodturning" while sitting in the library ; ). I happened upon the following in the Glossary section of the book.

"Maker: A descriptive term of both affection and compromise, but with very little baggage as compared with artist or craftsperson. The term maker is inclusive of both artists and craftspersons whether they be self-taught, apprenticed, or school-trained; isolationist or egocentrists; highly creative, or just mildly confused."

Good "Big Tent" terms for what we do.

When people ask me "What do you DO?" My answer is usually

"I take larger pieces of wood, sometimes expensive wood, and with the help of tons of cast iron, the energy equivalent of a medium sized herd of horses, a host of very sharp tools and complete disregard for my own health and safety, and with a completely unjustifiable expenditure of time, energy and sometimes even actual skill - convert it into smaller, valueless, hard to dispose of STUFF. Every once in a while - I make something useful or nice to look at and/or play with."

The person who asked is, of course, usualy gone before I've completed my answer ; )

Next time I'm asked, I think I'll start with "I'm a maker." and if there's a follow up question - provide the Long Answer.

So how do YOU answer the question "What do you DO?"

Re: Way To Get Past Artist or Craftsperson

#2

Not exactly the question(s) I get

George Guadiane

How did you do that?

How long did it take you to make that?

Where did you get the wood for that?

What kind of wood is it?

Is it rare wood?

How much did the wood cost you?

I presume, for the most part, that the turned pieces speak for themselves.

My answer to YOUR question would be: I sell antiques and collectibles on eBay.

"What do you do for fun? might get me closer to your answer... And if you start by excitedly grabbing their sleeve or their arm or something, you'll get to finish your answer before they leave. :D

Re: Way To Get Past Artist or Craftsperson

#3

Re: Way To Get Past Artist or Craftsperson

Terry Scott

I say I am a Woodturner but that is a crude name for what I am know producing

I have taken this to an artform

everyone agrees , we then go on to discuss how the piece they have selected could well be an heirloom or on the Antique road show in the future

Being a one off also is another notch that is good to convey

Re: Way To Get Past Artist or Craftsperson

#4

Re: Way To Get Past Artist or Craftsperson

Russ Fairfield

It always makes for an interesting argument, but the only opinion that matters is that of the customer with the money. If you are famous, you can call yourself an "artist" and you can sell your bowls for $700 or more. If you aren't famous, you are just another unknown "craftsman" who is lucky to get $100 for the same bowl.

Re: Way To Get Past Artist or Craftsperson

#5

Steven Antonucci

I make stuff

Steven Antonucci

Sometimes, I use a lathe exclusively. On those day, I am a turner. Somedays, I just make stuff...

Steve

Re: Way To Get Past Artist or Craftsperson

#6

Steve Kubien

Re: Way To Get Past Artist or Craftsperson

Steve Kubien

When people ask what I do I say, "I am a woodturner."

Then: What's a woodturner?

Me: I take pieces of wood and make round stuff.

Of course it's a kid and I am feeling nasty or the parents have p*ssed me off, I'll tell them, "I am the creature that lives under your bed!"

Re: Way To Get Past Artist or Craftsperson

#7

Re: Way To Get Past Artist or Craftsperson

Bill Grumbine (Kutztown PA)

I like Art Liestman's line: "I just make stuff."

Re: Way To Get Past Artist or Craftsperson

#8

Re: Way To Get Past Artist or Craftsperson

Don Orr

I work for a living and turn for fun and sanity.

Re: Way To Get Past Artist or Craftsperson

#9

Re: Way To Get Past Artist or Craftsperson

Ken Grunke from SW WI

and I can't remember where it came from or who said it but it's:

"One who works with their hands is a laborer.

One who works with their hands and head is a craftsperson.

One who works with their hands, head and heart is an artist."

Re: Way To Get Past Artist or Craftsperson

#10

None Of The Above: Upper Management

charlie belden

They get other folks to use their hands and head and heart,

then take the credit. Well that's how some management

people seem to do it. The good management person takes

care of their people, getting them the time, materials and

whatever is necessary to get the job done and makes sure

that credit goes to the people who did the work - be it bonus

money or merely Atta Boys.

Have worked for both extremes - and a lot more got done

and done right - working for the guy who stressed "You

can't have it Fast, Good AND Cheap. Pick two and we'll

get it done."

Re: Way To Get Past Artist or Craftsperson

#11

Re: Way To Get Past Artist or Craftsperson

Robwallace

Ken:

(St.) Francis of Assisi:

"One who works with their hands is a laborer.

One who works with their hands and head is a craftsperson.

One who works with their hands, head and heart is an artist."

Rob Wallace

Re: Way To Get Past Artist or Craftsperson

#12

Re: Way To Get Past Artist or Craftsperson

Rob Wwallace

Ken:

(St.) Francis of Assisi:

"One who works with their hands is a laborer.

One who works with their hands and head is a craftsperson.

One who works with their hands, head and heart is an artist."

Rob Wallace

Re: Way To Get Past Artist or Craftsperson

#13

Re: Way To Get Past Artist or Craftsperson

Allen Neighbors

"I make health items for the home." And then, if they want me to elaborate.... I say, "I make wood-turnings, and since they are nice dust collectors, they promote your good health, because you don't breathe the dust."

Re: Way To Get Past Artist or Craftsperson

#14

want to really confuse them?

john lucas

When they ask what you do say "I make conseptual pieces". That's where I'm headed next year. They will probably have some turning involved and some maybe totally turned but they all start with an idea. A simple work, thought, or concept. Then it's up to me to figure out how to make it a visual statement.

Re: Way To Get Past Artist or Craftsperson

#15

Re: want to really confuse them?

charlie belden

Concept pieces are probably the most fun - when they work. The pieces take on a personality and a voice as they are being done - often leading to a completely different final concept.

You can also do Reverse Concept pieces - where the finished piece generates its own story - leaving you to write it down, and maybe embellish it with interesting details. These are another type of I Meant To Do THAT pieces. The better you can Spin A Yarn, the better the piece may be received, not that I'd EVER do THAT ; )