Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Serendipitous Swivel Joint Idea

Posts

Serendipitous Swivel Joint Idea

#1

Serendipitous Swivel Joint Idea

charlie belden

Must be something in the air. This is another example of Synthesis - and serednipidous synthesis at that.

I'm playng with an Arduino "stamp controller", fiddling out how to use sensors to activate actions - lighting up LEDs, buzzing a little buzzer and controling a servo. While playing with getting an infra red sensor detecting movement to then buzz buzzer, I turned a "funnel" to put over the buzzer to "amplify" its sound (Serendipitous element #1).

I was thinking about using the Arduino in a hollow form - with an infra red detector to spot movement nearby and then triggger LEDS, RDG LEDS, a piezo electric "speaker" and maybe a servo to add movement.

I'd turned a hollow form intended to go over a hidden light and sound activated micro-robot which would cause the piece to crawl away when touched or startled by a loud noise - like a hand clap. I wasn't able to get its weight down to the micro robot's carrying capacity but kept the piece on a shelf. Tried using it again for a Mag Lev idea - which also didn't work out using this piece. But - third time's the charm - it would be perfect for a prototype for a "stamp controller" dynamic piece. (Serendipitous element #2).

Wth this hollow form AND an Arduino breadboarded IR detector and piezo buzzer - with the "sound amplifier" funnel shaped "speaker cone" - on my desk next to each other I had an "I WONDER IF . . ." thing happen.

Hmmmmm - that "speaker cone" looks like it's a little larger in diameter - than the opening in the top of the hollow form.. Wonder if it'll fit inside - or if it'll stick up too much? So I dropped the "speaker cone" in the hole in the top of the hollow form - and the rim of the former fit almost flush with the rim of the opening in the hollow form. Hmmmm. . . .

When I put my finger in the "speaker cone" to remove it from the hollow form - it swiveled around.

Hmmmmmmm! If I were to put a tenoned finial down into the "speaker cone" - it could swivel around - remaining vertical even when the hollow form is tilted. And if there were a counterweight off the bottom of the finial's tenon - it could pendulum - like a ball and swivel socketed finial I'd played with earlier.

As luck would have it, I HAPPENED to have a bunch of "spires and spinarettes" that I'd turned a few years back - on hand. (Serendipitous element #4).

So here's a line drawing of the idea.


And here's a cell animation of the hollow form - with funnel and finial that hopefully convey how this idea works.


Comments, questions, suggestions all welcomed.

Re: Serendipitous Swivel Joint Idea

#2

Let's try the Animation Cells again

charlie belden

Well the GIF animation doesn't seem to work so let's try the "cells" that are

in that animation as a series of still shots.


Tinial: a Tilting Finial

Re: Serendipitous Swivel Joint Idea

#3

Re: Serendipitous Swivel Joint Idea

Mark Mandell - Gone Round In Jersey

Charlie,

Do you live in Milwaukee by any chance?

Can't help but think of Rowan & Martin's Fickle Finger of Fate award.

Have fun. :D

Re: Serendipitous Swivel Joint Idea

#4

To Illustrate My Question

Mark Mandell - Gone Round In Jersey


Re: Serendipitous Swivel Joint Idea

#5

Re: To Illustrate My Question

charlie belden

I'm betting the contractor, when asked about the leaning thing, insisted that he meant to have them tilt, that one or two are always SUPPOSED to tilt- and that the PLANS were wrong.

Wouldn't it be an attention getter and conversation starter if a church had their bell attached to the cross on their steeple, the cross rocking back and forth as the bell tolled?

Re: Serendipitous Swivel Joint Idea

#6

He He

Mark Mandell - Gone Round In Jersey

the pic was taken by my couz from his balcony. He informs that the Leaning Finial of Milwaukee is the subject of not a few outstanding bets as to when it's going to fall and take the dome with it.

I, for one, would not be pleased to enter the structure in question. ;)

Re: Serendipitous Swivel Joint Idea

#7

Re: Serendipitous Swivel Joint Idea

Bob Macgregor

Charlie,

I think friction between the cone and the rim of the HF might inhibit the rocking action. This could be overcome somewhat by a very fine finish and maybe some sort of lubrication, by bearings OR by introducing a slight air flow into the pot (ie modest air levitation). With an air cushion, the top might wobble continuously on its own, or it might just reach some equilibrium point cocked over to one side...I don't know...a pendulum weight on the bottom of the cone would help keep it centered. If the opening of the HF and the cone OD are both round and a fairly good seal, it wouldn't take much airflow to support the cone.

BOB

Re: Serendipitous Swivel Joint Idea

#8

Re: Swivel Joint

Mark Mandell - Gone Round In Jersey

Better chance with a gimbal mount than air. Air suspension in concave forms needs the air supply feed at the bottom geometric center to balance the airflow out to the rim plus a very precise match between to two surfaces. He'd have to put sufficient weight in the bottom of the moving form to drop the c-o-g below the rim for the finial to stay upright.

Learned something about this in grad school from a sculptor who was doing kenetic work using air flotation with concentric spun metal bowls.

Re: Serendipitous Swivel Joint Idea

#9

Re: Swivel Joint  *LINK*

charlie belden

I guess I should have made it clear that the intent is NOT to get the finial to pendulum with the piece below stationary. What I had in mind is that the PIECE move (tilt/rock) and the FINIAL REMAIN VERTICAL.

The YouTube video of Wibble Wobble shows a piece that utilizes the basic pendulum finial idea - but uses a ball and socket "swivel joint". While THAT joint - a concave hemisphere "socket"in the top of the piece - and a convex hemisphere "ball"on the bottom of the finial - isn't that difficult to do, it does take more skill than making somethings we "occassioanally" do - inadvertently - make holes and "funnels" (OK, so maybe I'm the ONLY ONE who has ever turned through the bottom of a piece ; ) ).

So even a newbie - with a scroll chuck or jam chuck - can make a funnel - turning a hollow form may be

out of range - but a round hole in the top of a lidded box is something within range of a relative newbie. And turning a finial between centers. with a tenon that'll fit in the "funnel" ain't hard to do either.

This swivel idea seems to be one anyone can do - and maybe - come up with some fun uses for it.

Now about the "friction issue" between the cone sides and the sides of the hole, if the rim around the hole is rounged there won't be much contact area with the outside of the "funnel". And since most "holes" in the top of hollow forms often don't stay perfectly round, the contact area is even less. A little wax on the two parts would reduce the friction more - but with this Proof of Concept piece, it isn't necessary.

I like the idea of the "cushion of air levitation". A little fan unit like the ones used to cool the hotter running CPUs in PCs, controlled by - of course - a stamp controller - could let you vary the amount of air being put out. Pulsing it could cause the funnel and attached finial to bob up and down - while it's swaying.

Hmmmmm . . . .


WibbleWobble with Pendulum Finial

Re: Serendipitous Swivel Joint Idea

#10

Fan

Mark Mandell - Gone Round In Jersey

That's a different idea for sure.

A fan will need vents in the bottom of the vessel to draw air into the jar. Otherwise the blades will simply beat the air around inside.

Re: Serendipitous Swivel Joint Idea

#11

Re: Fan

charlie belden

"A fan will need vents in the bottom of the vessel to draw air into the jar. Otherwise the blades will simply beat the air around inside."

Not a problem with this prototype piece. Intended originally to be carried by a sound activated micro-bot - it has plenty of holes underneath - failed attempts to get its weight down to 62 grams (a bit over 2 oz). Not

easy getting a piece 5" in diameter and 3 1/2" tall down to.


This piece has served as two previous attempts at prototypes - the micro-bot idea that eventually worked for a sugar bowl with lid - and a MagLev idea using magnetic repulsion to suspend the piece over its base. Third time may be a charm for this piece - a stamp controlled piece with motion detectors controlling LEDs and a buzzer and maybe even a cell phone vibrator.

Seems like Wild Hare Ideas produce more Wild Hare Ideas - just the way Actual Wild Hares do ; )

Fan levitation! Would never thought of that. (OK, I might have thought of that, but it would require a bit of sleep deprivation, a lot of caffiene (Coca Cola) - and some hypoglycemia. Maybe if I added just a little bit of decent scotch . . .

Re: Serendipitous Swivel Joint Idea

#12

Re: Fan

Bob Macgregor

And if the base of the finial also had very fine spiral grooves, then air levitation would rotate it. I think the biggest challenge for air levitation may be the gymballing effect you are looking for. It is hard enough to get a good socket match that is purely rotational, but would be even more challenging when you have to maintain the match as it rotates and rocks/swivels side to side.

You really seem to like challenges, Charlie.

BOB