Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Some work in progress

Posts

Some work in progress

#1

Steven Antonucci

Some work in progress

steven antonucci

Here are two vessels that I started this week. Both were on and off the lathe within 2 hours start to finish. There is some sanding work to be done, but not that much beyond that.

Vessel #1

Spalted Chestnut. This was a very easy vessel to cut, since I made a large opening. It is cut end grain orientation using a hook tool on a 3/4" boring bar. The hook removes a lot of wood very, very quickly. In most areas, I would get 2 or 3 pulls before I had to clear out the curlies. I work about 3-4" at a time, so there was more time with the lathe off than on.

The wood was hard, but soft too (how can that be you ask?) No matter what tool I used, it tore out horrifically. One of the guys fromt the club was looking at the other piece of the log and walked away from it when he saw the chainsaw cut I had made because it was so ragged. When he saw the vessel, he went back out and grabbed part of the log. I told him that the only way he could possibly turn it was if he could use a skew, which is what I made my final pass along the length of the vessel with. There is some torn end grain along the rim that I had cut with a very sharp detail gouge, and I think I'll be able to powersand it carefully. About 13" tall.


Vessel #2

Redwood root burl. Even though my buddy Dan gave me this wood, it wasn't free. Sorta. We split this piece and I took one half and I put the other half in his truck the the club. Embedded in it was a large rock, which I detected with my chainsaw. End of cutting. We knew it was there, and I was cutting around it, right up until the point that I wasn't cutting around it. There's no mistaking the sound of a rock.

I had cut the piece along this rock to include the two inclusions. Nice thing about hollowing vessels with inclusions is that you can measure them very easily AND you clear chips out much more quickly. As a bonus, if your lighting is right and you have a big enough inclusion, you can actually see the tool while the lathe is spinning. Makes work like this very quick.

As it turns out, this vessel also had a couple of smaller rocks that I didn't see immediately. One came out with a gentle tug. The other one, I used my Oneway bowl gouge's built in detector. It goes tikka tikka tikka when you are cutting, and acts sort of like a SawStop for the lathe (blunts the edge so fast , you can't get cut...) After a few minutes on the Tormek, I was back in business.

Hollowed to 1/4" thick more or less all the way down except the bottom, which might be 3/8". The extra weight keeps them from getting knocked over by rampaging kids. 12" tall. Still needs some finish sanding, but pretty clean cutting with conventional tools.


My big debate is on finishing? Hate the idea of touching the whiteness of the Chestnut. Know that the redwood is going to soak up and darken. Decisions, decisions- have been leaning towards sanding finely and being done...

Comments, thoughts, criticism all welcome.

Steve

Re: Some work in progress

#2

Re: Some work in progress

GaryG in MD

Nice work, Steve. I'm in awe of the way you pump these things out.

I don't like raw wood "finish", but I guess you can just put on some wax. If you want to keep them light but get a little more finish on them, I'd go with CAMS (clear acrylic matte spray). After a few coats, you can buff it up to whatever degree of shine you want -- it doesn't stay matte if you rub on it a bit. I've used it successfully on several pieces. ...Gary

Re: Some work in progress

#3

Re: Some work in progress

charlie belden

While the small opening in the redwood is impressive to a wood turner, I'm putting my money on the chestnut selling first - more familiar porcelin vase like.

Of the two, the chestnut will probably present fewer challenges when it's time to apply a finish. Cherry is proned to splotchies - but redwood, especially burl can make cherry seem a dream to finish. But without a finish, redwood seems to actract everything - especially things that can stick to it, or sink into it. Super blonde or platina dewaxed shellac helps some - but . . .

And these were done with a hand held ring tool - without laser - with almost a foot of tool out in front of the tool rest? And in spite of that - you came up with TWO very nice looking pieces - in under 2 hours (each?)? Impressive - as usual.

Did you use the skew at the end as a negative rake scraper or did you make a final shear cut? Inquiring (nosey?) minds have to ask.

Re: Some work in progress

#4

Steven Antonucci

Why scrape when you can cut? :-)

steven antonucci

Nah, I skewed spaghetti like strands from the high point all the way down under the foot and then same thing up to the rim in the other direction. The finish is actually sanded starting at 180 grit which evened off the difference between the end grain and the side grain. I tried to cut the small cove in the neck, but negatory...

I should shoot a short video of hollowing with a hool tool. It's amazing how quickly the work goes when you cut instead of scrape...

S

Re: Some work in progress

#5

Re: Why scrape when you can cut? :-)

John Jordan

Sand it and wet it several times, until there's no patchiness, the last time it will be very matte/velvet looking. No finish is OK. :)

John

Re: Some work in progress

#6

Re: Some work in progress

Dinyar Chavda

Man you're fast, Steve, and yes, I, for one, would love to see that video of you using the hook tool, as well as how you make one.

Re finsihing the chestnut: According to Ye Olde Curmudgeon, also known as the Sage of Idaho, the finish that will impart the least color would be the relative new WaterBased Laquers from either Deft or General Finishes. One caveat, though, you have to sand between layers of finish.

Re: Some work in progress

#7

Steven Antonucci

assume you meant the redwood?

steven antonucci

Do you wax your unfinished pieces- or are they truly natural?

I'm guessing I'll have more time in sanding the redwood than turning it...

Steve

Re: Some work in progress

#8

Re: General Finishes High Performance.....

JamieDonaldson

...is an excellent H2O finish that will maintain a nice clear finish without yellowing like most oil finishes. I generally apply 2 base coats, then sand back for the final 3rd coat.