Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

large pin chuck

Posts

large pin chuck

#1

large pin chuck

john lucas

I'm always looking for ways to hold small parts when carving. I used to use what we call a pin chuck when cutting small parts for camera repair (or jewelry).

I had a PVC handle that I made that uses R8 collets similar to the Big Stick tool handles. I wrapped string around the end to keep it from splitting from the wedge action of the collet. It's perfect for anything that has a tenon. In this case the walnut part had a 3/8" tenon so I used a 3/8" collet. I have collets from 1/8" up to 3/4 so this is really going to come in handy.

I may rig up a way to hold this in my bestwoodtools carving post. Then it will be really handly.

Re: large pin chuck

#2

Steven Antonucci

Use a hose clamp instead of string

steven antonucci

I thought that was a collet? I wouldn't call it a pin chuck?

Neat idea, though...

S

Re: large pin chuck

#3

Re: large pin chuck

Bob Macgregor

I wonder if a modified fly-tying vise would do this job, too?

BOB

Re: large pin chuck

#4

Re: Use a hose clamp instead of string

John Lucas

Steve I actually use it as a handle for my smaller hollowing tools. I have hollowing tolls with tangs from 3/8" to 3/4". Using the BigSTick tool handles and different collets I can mount any of them in these tool handles. It's handy when I'm not using the boring bar.

I should have called it a Giant pin chuck. :)

Re: large pin chuck

#5

hose clamp keeps poking you

John Lucas

Steve I still have a couple of tool handles with Hose clamps, thanks to a demo by Clay Foster too many years ago to mention. They do work but It's too easy to catch that loose end on things. For this purpose I just needed something to act as a ferrule to keep the PVC from splitting. String, lashed on and soaked with thin CA works really well. I have a skew that I made this way and it's at least 10 years old and still working.

Re: large pin chuck

#6

Re: large pin chuck

Dick Strauss

John,

If you want to mount something round, take an old drill chuck from a cordless drill that doesn't work. Mount it in whatever handle you like! It will hold your homemade skewchis, gouges, hook tool or anything with a round shaft. It is also great for drill a depth stop hole by hand. My chuck tool goes from 0-1/2" and is tightened by hand.

Re: large pin chuck

#7

Re: Use a hose clamp instead of string

fgvanatta

I thought that was a collet? I wouldn't call it a pin chuck?

Me, too. A pin chuck normally is a shaft/tenon/whatever with a flat that a round "pin" sits on and tightens in the hole when the piece is rotated. Hence the name: "pin" chuck.

Frank

Re: large pin chuck

#8

Giant pin chuck

Ron Sardo


Re: large pin chuck

#9

sorry for the confusion

John Lucas

What I grew up calling a pin chuck was a small chuck designed to hold small parts that you could not hold with your fingers.

I realize now that what we turners call a pin chuck is a shaft with a flat area that holds a pin. This is inserted into a hole in the wood and rotated so the flat acts like a ramp and rolls the pin over to tighten it into the wood. I use one that I built when I turn wine stoppers.

Hope that clears up the comfusion.

Re: large pin chuck

#10

Re: large pin chuck

John Lucas

True Dick but they leave 3 nasty dents in the wood and will release the wood if you create very much vibration. I have 3 or 4 that I use for various things. The collet won't do that but does require that the tenon be with .010 or so of dead on or it won't close properly.

Re: large pin chuck

#11

Good photo Ron- they make pin chucks up to 1"

John Lucas

Re: large pin chuck

#12

Yes, made one myself

Ron Sardo

Don't really use it much, it worked well for the one project I needed it for.

Re: large pin chuck

#13

MrRules

Re: Yes, made one myself

MrRules

hey Ron, you still mad at me?

Stu

Re: large pin chuck

#14

Re: sorry for the confusion

Texian

So THAT'S a pin chuck. Thanks John. I thought it was a clamp for holding a pin while you engrave the works of Shakespeare on the head of the pin.

Re: large pin chuck

#15

Pin Chuck Vs. Pin Vice

Barry Irby

Seems to me you were thinking of a pin vice. I have one that hold very small drill bits. It actually has a little collet like the one you show, but well under a 1/16"

If this thing spins on the lathe, I would not want a hose clamp on it. Those things are deadly.

Re: large pin chuck

#16

15 hours and counting

Barry Irby