Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

One of those "days"

Posts

One of those "days"

#1

Steven Antonucci

One of those "days"

steven antonucci

Last night, I chucked up a piece of spalted wormy maple. I was almost done (maybe 2 more cuts?) when I got careless with the tool and destroyed the vessel (removing the tool, not even cutting... I wouldn't have really cared, but I had this piece of wood for 4 years or so before yesterday... bummer ro leave with nothing.

Fast forward to today, when I was turning a natural edge ambrosia maple hollowform. Same careless tool issue, knocked the bark off of it... found it and was going to glue it on afterwards... I was cutting the underside of the entry hole, and I knew I was out of tooling, so I made a quick swan neck tool and I got another small catch pulling it out. @3/16" there is no such thing as a small catch... more fancy firewood.

When winter comes, I will have the opportunity to relive all of these failures one last time. Took the kids to the park to fly the new kite, and it's missing a piece and there was no wind...

I'm calling it a day. Tomorrow promises to be better, though. A friend is moving, and he is not taking his wood with him. Told me I have first dibs on anything I want, including the burls :-)

S

Re: One of those "days"

#2

Re: One of those "days"

Terry Scott

Yep we all have days like that But like you all comes good

Re: One of those "days"

#3

Mike Stafford

Bounced off my faceshield....

Mike Stafford

It has been a long time since I have had a bad case of the stupids.

My friend Ed Moore taught me the acronym "S A F E R" which is to remind one to check these things:

S- Speed, make sure you know what the speed is when you start the lathe

A- Aside, stand aside when you turn on the lathe

F- Fasten, make sure the chuck, banjo and tool rest are secure

E- Eye protection, safety glasses are a must, a face shield is the best option

R- Rotate; spin the lathe before you turn it on to make sure the stock clears the tool rest and ways

Well, I got an F on F as I forgot to tighten a chunk of wood tightly in the chuck and as soon as I put the gouge to it it flew out and bounced off my face shield hitting me right in the kisser.

My lips are bruised ladies so you will have to wait a day or two before I can return to the kissing booth... :b :D

Thank goodness I was wearing my face shield.

Re: One of those "days"

#4

Must be in the cards today.

john lucas

I've been practicing thread chasing. I cut the female thread, measured the male thread and then cut the tenon too small. Fortunately I am testing using epoxy for the threads so masked off the piece and poured more epoxy. The frustrating part was I did the same thing last night on the same box so I'm filling it for the second time.

I did get 2 other boxes done with threaded lids. These were started last week when I did 2 threading demos for the local clubs. I was going to toss them because I didn't take the time to completely hollow them. I was able to make a jig to hold the top so I could finish hollowing it and then finished off the bottoms as well.

Re: One of those "days"

#5

Re: One of those "days"

George Guadiane

Might be something in the air!

Thursday, I turned a piece of curly koa that was VERY punky. It didn't blow up, but the box I was TRYING to make didn't look very good because of the wood...


I ALSO tried to remove the tenon from an ambrosia, curly, maple burl hollow form with green spalting...

It had already started to move, but it was well reverse mounted. I managed to leave tool marks while trying to make a "pretty" foot... TWICE. The second time there was nothing left to recover with, so I have tool marks. It already has a finish on it so, I COULD hand sand the base and try finishing again, but I figure I'll have to sand off ALL of the finish and even then I won't get an even acceptable finish.


Re: One of those "days"

#6

Re: Must be in the cards today.

Fred Holder

Hello John,

I think all of us occasionally mess up and make the male thread tenon too small, I know I do. However, if I carefully use the following drawing, I have less problems:


This drawing is from my book, Making Screw Threads inWood, which is not out of print, but there may be a few around. I may have posted this before, but don't remember.

Re: One of those "days"

#7

Re: Bounced off my faceshield....

Russ Fairfield

He got that from Keith Rowley's book, and it is always good to be SAFER.

I am losing the nail on my left index finger because I did not obey the "A" for "Aside" and the wood came apart when I turned the lathe on. I'm lucky it is only a finger nail because I wasn't wearing a face shield.

Re: One of those "days"

#8

S A F E R

Ed Moore in SW VA

1. Mike, I am glad that your injuries were no worse and that you will be recovered in time to kiss all your students and the assistant at JCCFS. :D :D

2. I got S A F E R from Don Riggs, who got it from ... , and it may well go back to Keith Rowley. Don is a very talented woodturner who moved from the Capital Area Woodturners down to Smith Mountain Lake Woodturners and Blue Ridge Woodturners. Many novices have benefited from his shared expertise.

3. I am beginning to think that the Robust toolrests, which allow the fulcrum to be closer to the work, should be added to the list of musts/safety tips. In using the Powermatic toolrests at JCCFS I found it necessary to have tools hung over the rest too far. In one such case a small bedan broke in half when it touched a piece of oak burl. No injury resulted, but it sure woke us up.

Ed

Re: One of those "days"

#9

Fred  I just go in a hurry and screwed up

john lucas

I don't have any problems getting the tenon the right size when I dn't do something stupid. I just got in a hurry and took too big of a cut. You can't add wood back on. Well in this case you can because it's epoxy. I'll sneak up on it next time and not be in such a big hurry.

If we look back I'll bet most accidents happen because we either get in a hurry or we aren't paying attention.

Re: One of those "days"

#10

Re: S A F E R and Riggs

Ed Moore in SW VA

I got an email from Don Riggs and he said that he did get S A F E R from Keith Rowley's book, so the chain is shorter than I suggested. Since I teach S A F E R too, I will be careful to credit Rowley in the future.

Ed

Re: One of those "days"

#11

Steven Antonucci

What a difference a day makes

steven antonucci

I just got back from my buddy Dan's house, where we spent the morning loading up our trucks with the stuff he's giving away to me and to the club we belong to (Water Gap Woodturners). There's another truckload at least waiting for us, possibly two truckloads...

Here are some of the highlights:

Redwood burl and dried walnut...


Note the rock in the redwood that I ALMOST cut around successfully without hitting...

Pin Oak burl, American Chestnut, and big leaf maple burl...


His truck looked like my truck, and we're giving it all to the WJW club (his truck, not mine! :D ) Feel free to call me names for this drive-by gloat!

Steve