Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Need WC Help - Stop Collars

Posts

Need WC Help - Stop Collars

#1

Need WC Help - Stop Collars

bowlman

I need your help, please. Does anyone know where I can get some stop collars with a 1" inside diameter? None of the box stores around here carry them.

Thanks in advance!

Re: Need WC Help - Stop Collars

#2

Re: Need WC Help - Stop Collars *LINK*

Dave Peebles Lyons, Ohio

Hi Dick,

Will these work for you?

Dave


Stop Collars

Re: Need WC Help - Stop Collars

#3

Re: Need WC Help - Stop Collars *LINK*

Bill Turpin in WNC mountains

Try this: also MSC, Grainger, Enco


collars

Re: Need WC Help - Stop Collars

#4

Mike Mills

Re: Need WC Help - Stop Collars

Mike Mills

You didn't say what the use was for.

If only to hold the tool rest a certain height while you swivel it to a new position (and then lock it down again) I use hose clamps from Autozone. They have some with a large thumb screw which makes it easy to adjust. No fiddling around with an allen wrench. They are about $3 for a package of two.

Mike

Re: Need WC Help - Stop Collars

#5

Re: Need WC Help - Stop Collars

robo hippy

In the "I am too cheap to buy one" category, turn an end grain cylinder 1 1/2 inch or more in diameter, bore it out with a 1 inch forstner bit, then ream it a bit with your favorite hollowing tool, and cut to length. If you want to get fancy, you can make about a 1/16 recess along most of the length, and wrap it with colored nylon string construction string. Stronger than the plastics, and it won't shatter.

robo hippy

Re: Need WC Help - Stop Collars

#6

Rob Wallace

Re: Need WC Help - Stop Collars

Rob Wallace

I buy mine from our local Farm Supply store (Theisen's), but any store which caters to agricultural implements and supplies (e.g. Tractor Supply Co., AgriSupply, Agway, Farm & Fleet, etc.) should have 1" ID stop collars with set screws. I have several, and use them on my tool rest shafts to set the height for one-hand rest re-positioning.... I also use them on my MacNaughton coring tool rest to re-set the tool to center-line each time. Very useful accessories at less than $ 1.50 each.

Should not be too hard locally to find before you have to move to Enco, MSC, Grainger, etc, via catalogs or on-line.

Rob Wallace

Re: Need WC Help - Stop Collars

#7

Re: Need WC Help - Stop Collars

bowlman

Thanks everbody! WC is such a great resource!

Re: Need WC Help - Stop Collars

#8

Dick Hines

Re: Need WC Help - Stop Collars

Dick Hines

I made a collar for my coreing rig. I just cut a piece of gray electrical conduit to the right height and set the tool rest in and it is always on spot.

Re: Need WC Help - Stop Collars

#9

or...

GaryG in MD

If I don't need high accuracy, I just cut an old wine cork to length and drill through the middle of it. With the cork on the drill bit, go to work. ...Gary

Re: Need WC Help - Stop Collars

#10

Rob Wallace

Re: or...

Rob Wallace

Gary:

I think bowlman was looking for a 1" inside diameter stop collar (actually, a shaft collar) for use on a tool rest post. I don't think he would be using this for drilling, but this is a good tip. Not sure a cork would fit the bill for a 1" tool rest positioner.... unless is was a cork from a Grande Reserve Super Magnum Bottle! That would be one whopper cork!

Also - bowlman - I forgot to mention..... When I use a shaft collar on the tool rests that need to be adjustable, I replace the set screw with a thumb screw and can easily make fine adjustments as necessary.

Rob Wallace

Re: Need WC Help - Stop Collars

#11

Re: or...

GaryG in MD

You're right, Rob. I allowed too much time between reading the post and replying to it with generic "stops" in my head. Corks do work well for little stuff. ...Gary