Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Steady rest question

Posts

Steady rest question

#1

Steven Antonucci

Steady rest question

steven antonucci

For folks that have made steady rests, do you find that the wheels bruise the wood where you held it? I have a vessel that I used my steady rest to support, and I have a very distinct ring where the wheels were. I'm having a bear of a time sanding it out...

Wheels are clear, so it's not a stain... just a spot where the wood looks compressed. Any advice on wheel size or similar is appreciated...

Steve

Re: Steady rest question

#2

Re: Steady rest question

Allen Neighbors

Steve, mine does bruise the wood if I press the wheels against the wood when I tighten them down.

To solve the problem, I suggest to just let the wheels "kiss" the wood when tightening them down. They'll still leave a faint mark, but it'll be easier to sand away.

I've found that the rest still does the job it's designed to do, when the wheels aren't so tight.

Re: Steady rest question

#3

Re: Steady rest question

Carol Reed

I don't know that I would try to sand it out. The wood fibers are compressed somewhat from the turning of the wheels of the steady rest. I would think that all you would wind up with would be a divot.

I might try to un-compress them by wetting them with distilled water. After the grain is again raised, then sand.

Just a thought....

Then, again, make it a design issue. hehehehe

Re: Steady rest question

#4

Eduardo Sarmiento

Re: Steady rest question

Eduardo Sarmiento

Masking tape the piece where the weels touch?my2cents

Re: Steady rest question

#5

I'm with Carol on this....

Barry Irby

I'd wet it rather thoroughly before I sanded. Otherwise, it will never go away. That's my opinion based on no experience. I'm borrowing Carol's intuition. And in the future I would use the tape and the kiss principle. Wrap the tape in the right direction.

Re: Steady rest question

#6

Blue Masking Tape....

Wally Dickerman in Arizona

Blue, because it doesn't leave a residue and comes off easily. Also,use a little less pressure. I can't recall ever damaging a piece when using a steady rest.

I used a steady rest this morning on a camphor burl HF. Camphor is quite soft...no damage or tape residue.

Wally

Re: Steady rest question

#7

Steven Antonucci

The bruise in question

steven antonucci


The rest of the vessel is sanded to 320 and lightly buffed. A good 320 finish next to a slight bruise is just about the same thing as putting highlighter on it and circling it.

This vessel goes out the door on Monday to its new home. Guess what I am doing tonight?

Steve

Re: Steady rest question

#8

Re: Steady rest question

Carole Valentine

I cover the area that the wheels will contact with several layers of painters tape. iT helps protect. You may be able to draw out the compressed fibers with water as Carol suggested or you can go one step further and use a wet cloth towel and an iron to apply steam heat...just be careful and don't apply the iron too long in one place. I have had much success repairing dents, dings and other "compression" type defects in wood using this method.

Re: Steady rest question

#9

Re: Steady rest question

Carol Reed

I wonder if one of those steamer devices for getting wrinkles out of your clothes would work. You know, the one they advertise by pointing it at a garment hanging on a hanger. Supposed to be good for clothing that just came out of a suitcase.

The reason I wondered, is to avoid the potential scorching of the iron and wet cloth method. BTDT!

Re: Steady rest question

#10

Re: Steady rest question

john lucas

Steve I haven't had a problem so far but I've only used mine on a vessel a few times. Mine has black inline skate wheels.

You might try using the clear cling wrap. I bought a roll from office max and it has a lot or turning uses. I wrap pieces that will check with it before turning. Hollow vessels that have large voids can be wrapped while hollowing to help keep them together. It makes great tape for gluing up some segmented vessels because it stretches and clings to itself.

Re: Steady rest question

#11

Re: Steady rest question

Carole Valentine

Won't know til you try it. Somehow I don't think that would work as well as the wet towel/iron. The secret to that is to have the towel good and wet and the iron hot enough to give a good burst of steam quickly so it doesn't scorch. I have never scorched wood yet, but maybe my day is coming! LOL

Re: Steady rest question

#12

Re: Steady rest question

robo hippy

I know there are different hardness ratings for the wheels, some softer, some harder, but basically you have burnished the marked area. A clothing steamer would probably work. I have removed countless dings from my flat work with water. Get it damp first, use a damp cloth of some sort, apply hot iron. I use one that I used for applying the mylar coating to my model glider wings, teflon coated, and small. You need steam, just getting it damp doesn't seem to work as well.

robo hippy

Re: Steady rest question

#13

Re: Steady rest question

steve worcester

Additionally, the wheels can leave track marks of urethane (or whatever the wheel composition is) that make for a difficult time with film finish adhesion.

Re: Steady rest question

#14

Why have I never had these problems?

Russ Fairfield

I have never had any problems with crushing the wood, skid marks, or any of the other things I see described; and I don't use tape or anything else to protect the wood. My skate wheels are clear, but they can't be that good because I bought them at WalMart, and they wern't their most expensive. Maybe I'm just lucky or my eyes are getting bad.

Having said this, I'll probably have problems with the next piece I do with the training wheels.

Re: Steady rest question

#15

Re: Why have I never had these problems?

John Jordan

Use a faceplate instead of a chuck, and an adequate bit of unturned wood for support near the base, and one probably doesn't need a steady rest. :)

I've done many 15-18 inch pieces and a few 20 inch tall pieces without a rest. Ellsworth has done 30+.

I guess that didn't really help, did it? Sorry, IDK. :D

John

Re: Steady rest question

#16

Re: Why have I never had these problems?

Carole Valentine

John, do you use a faceplate screwed directly into end grain? I never trusted that.

Re: Steady rest question

#17

Re: Why have I never had these problems?

Wally Dickerman in Arizona

Carole, for a secure way to securely fasten a faceplate to endgrain, especially soft, spalted etc., check out Reviews on WoW, Sept 30, 2003. It works.

Wally

Re: Steady rest question

#18

Re: Why have I never had these problems?

John Jordan

Carole, screws hold fine in end grain. I did hundreds that way with never an issue. Good screws help. I use SPAX screws. Highland Woodworking has them. They have very deep threads and displace minimal wood. Also, don't overtighten. I use #12 1-1/4" long. That's just a inch in the wood.

6 or 8, or 10 screws in a good faceplate makes a very strong mount. I alas don't use soft/punky wood.

Like most, I still use the chuck for most pieces, just not the ones that may flex and chatter. I used to make a point of using faceplates when teaching, but I've been beaten down. :)

John

Re: Steady rest question

#19

Re: Why have I never had these problems?

John K Jordan

Lissi Oland told me she uses stout sheet metal screws to hold huge pieces on a faceplate for turning (blanks 30" or more in dia). She uses gorilla glue between the faceplate and the wood.

JKJ

Re: Steady rest question

#20

Re: Why have I never had these problems?

Carole Valentine

Thanks, John. I think the one and only time I ever used them in end grain it was years ago on a piece of wet maple and they kept losing their grip. Now that I think about it, I can see that my mistake may have been the the wet wood - when the screws go in, mush comes out. LOL

Re: Steady rest question

#21

Re: Why have I never had these problems?

John Jordan

I only use wet wood. The problem was likely the screws and/or over-tightening. Sheet metal screws, though often recommended, aren't very good.

Here's a pic of the Spax screws-note the deep thread and serrated threads on the end. I used to use a manual screwdriver to put them in during demos-people were usually shocked, but they are that easy to drive.

John