Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Made a thin parting tool. Now how do I sharpen it?

Posts

Made a thin parting tool. Now how do I sharpen it?

#1

Made a thin parting tool. Now how do I sharpen it?

Scott Burr in Ben Lomond CA

I'll start at the beginning, I purchased a very nice 10" Japanese chefs a few years back from The Japan Woodworker. I was tried of my wife not taking care of my Henckels so I bought this one for me and me alone.


Well needless to say she didn't listen to me, and a few months later used it cut open a butternut squash and snap! She broke about 1" of the tip off. I was very upset >( but I got over it.

I cut off the rest of the tip with a dremel tool and reshaped and sharpened it to perform like a Japanese vegie knife see here:


Then it was my turn, I had the knife kick sideways on me carving a chicken and and took a nice chunk out out of the middle of the blade when I ran it into a bone :( .

It was time for retirement, or so I thought until I got a lathe started learning about turning.

So, Thanks to all of you it now as been reborn :)


So, I'm wondering how to sharpen this, The blade is laminated and looks like this at the tip:


In my usual off the wall thinking, what would happen if I filed down the softer inside steel and made it have a small flute like the fluted parting tools?


Or like this:


Maybe should I clip the tip off of it like the Sorby's thin parting tool?



Either way, How does one sharpen (Hone) a thin parting tool?

Also how would you define the cutting tip?

Re: Made a thin parting tool. Now how do I sharpen it?

#2

Re: Made a thin parting tool. Now how do I sharpen

Roger

Check out Jennifer Shirley's parting tool grind in the tool grinds area.

roger

Re: Made a thin parting tool. Now how do I sharpen it?

#3

Are you sure that the inside is softer?

Keith Newton----Little Rock, Arkansas

I would have thought it was just the opposite of how you stated it. The hard steel should be in the middle.

Re: Made a thin parting tool. Now how do I sharpen it?

#4

Re: Made a thin parting tool. Now how do I sharpen

Gordon Seto

Not knowing anything about Japanese knives, if a knife that snaps so easily, probably I would do a little more research about the character of the steel before converting it into some turning tool.

Re: Made a thin parting tool. Now how do I sharpen it?

#5

Ken Vaughan

Re: Made a thin parting tool. Now how do I sharpen

ken Vaughan

While the idea is good, the steel appears to be high carbon steel. The center material is probably pretty brittle, judging by the story and the breaking of the blade.

High carbon steel will lose temper as the heat at the tip rises above about 300degrees F and will soften, but become less brittle.

It is the brittle nature of the blade that should be of concern. Breakage with flying shards of steel is not a good thing.

This is not the tool for massive cuts or hogging out material. It may work just fine for delicate cuts and finese.

Re: Made a thin parting tool. Now how do I sharpen it?

#6

Steve Kubien

STOP!

Steve Kubien

Scott, I gotta agree with Gordon on this. I'm not metallurgist (sp) but if this thing is snapping on a butternut squash, I think you are going to get badly hurt at the lathe.

Be careful.

Steve

Re: Made a thin parting tool. Now how do I sharpen it?

#7

Thanks Everyone...

Scott Burr in Ben Lomond CA

Seeing how I'm new to this, I'll take your advise and scrap this one. I have another knife I can use.

Still, how does one sharpen a thin parting tool?

Re: Made a thin parting tool. Now how do I sharpen it?

#9

Re: Hii Roger, wheres the tool grinds area?

Bill Howatt

It's link is in a "fly-out" from the Odds 'n' Ends item in the menu block on the left.

Bill

Re: Made a thin parting tool. Now how do I sharpen it?

#11

Re: Thanks Everyone...

eliot d------WebKitFormBoundaryAo1Kz+awUUYH8ShA---

If we can forget about a curved, gauge-like cross section, then you sharpen it just as you would any other tool that has two edges that come together to form a sharp edge.