Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Belt Sander Sharpening Fixture *LINK*

Posts

Belt Sander Sharpening Fixture *LINK*

#1

Belt Sander Sharpening Fixture *LINK*

Jerry Hall

Here is a fixture that seems to be working out for using an old belt sander for sharpening. Cheap and safe for kids. Variation based on an article in "Woodturning Design" #25 by John Williams. See slide show below for examples of its use with most all tools.


img

Belt Sander Sharpener Slide Show

Re: Belt Sander Sharpening Fixture *LINK*

#2

Re: Belt Sander Sharpening Fixture

Carol Reed

Thanks, Jerry. That is helpful. I am using a 1" strip sander as opposed to a belt sander, so mounting the Wolverine under it is the challenge.

But if I can figure out the geometry of the pivot point and the belt, I think I can figure out a way to provide an in and out adjustment for the pivot point. What I liked about your picture was the alternative to the Wolverine.

Grey cells are stirred up.

Thanks.

Re: Belt Sander Sharpening Fixture *LINK*

#3

Geometry -  Belt Sander Sharpening Fixture

Henry (Raleigh NC)

Carol: I rec'd David Ellsworth's excellent book for Christmas: "Ellsworth on Woodturning". In it he shows a schematic that i used to create my own crude version of the sharpening jig.

The geometry he gives is to have the pivot point 7" away (horizontally) and 4" below (vertical) from the face of the sharpening media. His case is a grinder but this works for my disk sander approach too.

I am using this to sharpen a finger nail gouge, something Ellsworth refers to a an (Ellsworth) Signature gouge grind (or jig).

Henry

Re: Belt Sander Sharpening Fixture *LINK*

#4

Re: Belt Sander Sharpening Fixture

IAN

jerry

great setup and easy enough for most to construct, might even allow for a few experiments that can't be done on a grinder easily.

one question, what grit belt do you use.

IAN

Re: Belt Sander Sharpening Fixture *LINK*

#5

Gritty response

Jerry Hall

I am using 100 grit which lets me do a modest amount of shaping and still produces a keen edge "for all practical purposes." Of course the skew still must be honed. I am going to experiment with higher grits once all my shaping is done so that I might even end up with a "poor man's" Tormek.

John Williams mentioned he liked old worn out belts to produce a nice dressed edge. I would druther have the right grit from the outset tho.

All this said, I have but a few hours experience using this thing. So buyer beware!

Re: Belt Sander Sharpening Fixture *LINK*

#7

Steve Kubien

Re: Belt Sander Sharpening Fixture

Steve Kubien

Hey Carol,

When I used a 1" belt sander for sharpening I mounted a Wolverine-like rig under the wheel using a piece of t-track as the arm. Now, you need a way to create a pivot point. I put a bolt through a block of 1.5" thick beech and epoxied a couple of washers to the top to do this. The bolt can be loosen and tightened as required so you can move the entire block forward and aft. I cannot remember the height of the block but it was around 2" in order for the tool to hit the belt where the platen is. I have tried to find a picture of my former rig but, no love yet.

HTH

Steve

Re: Belt Sander Sharpening Fixture *LINK*

#8

Important-take the dust bag off

john lucas

I sharpened like that for several years. If you don't take the dust bag off the sparks will burn holes in it. This I learned when I saw smoke coming from it. :)

Re: Belt Sander Sharpening Fixture *LINK*

#9

Re: Gritty response

IAN

thanks jerry,

although I personally freehand grind most of my tools, I teach beginner turners to jig grind and some have a funding shortage that may allow them to get a lathe and a couple of tools. but not enough to purchase a full grinding setup.

I came up with a setup that works well using a grinder, but I still think the belt sander has possibilites that I may explore myself to give another set of options to new turners.

here's a link to the setup I currently help them build,

http://www.msswt.org/Tips/Ian's_Tool_Grinding_Fixture.pdf

ian

Re: Belt Sander Sharpening Fixture *LINK*

#10

Re: Belt Sander Sharpening Fixture *LINK*

Stuart Johnson

Take a look at Herm de Vries's set up. Look under tools and tips, scroll down to the sharpening part.


Herm de Vries 1 inch belt sharpening

Re: Belt Sander Sharpening Fixture *LINK*

#11

Ian, Nice setup for the grinder!

Jerry Hall

Re: Belt Sander Sharpening Fixture *LINK*

#12

Re: Belt Sander Sharpening Fixture

Ed Wujciak

Steve and Carol,

I also use a 1" strip sander for sharpening and I made a rig similar to Steve's description to use a Vari-Grind fixture. Mine is made of wood but is very similar to what Steve describes. I'd send a picture but I'm currently without a camera. One bonus of this system is that you never have to deal with a grinding wheel that's smaller and smaller and smaller....

Good luck