Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Quick, one hour plate in curly white oak

Posts

Quick, one hour plate in curly white oak

#1

Steven Antonucci

Quick, one hour plate in curly white oak

Steven Antonucci

It may have been a little bit more than an hour, but it wasn't 90 minutes. Rooting through the flat pile, I came across this piece of wood and threw it up on the lathe. A quick gold leaf accent and voila!

Clean cuts with sharp tools made the finish sanding minimal. Going into a gallery show in a few weeks, and I needed some pretty wood that hadn't been all covered with paint. 10" give or take, from a 200+ year old tree that I have 600 BF of lumber in storage...


Have enough of this wook to make about another 100 or so...

Comments welcome.

Steve

Re: Quick, one hour plate in curly white oak

#2

Don Pencil

Re: Quick, one hour plate in curly white oak

Don Pencil

Your mother must be very proud of you.

Re: Quick, one hour plate in curly white oak

#3

Re: Quick, one hour plate in curly white oak

John K Jordan

Nice wood. By the time you make the 100th one you should be down to 30 minutes!

I like turning oak but it doesn't seem to get used much. That wood might make some beautiful hand mirrors.

JKJ

Re: Quick, one hour plate in curly white oak

#4

I like it!

Scott in Falcon

I like the gold leaf accent around the rim of the plate. For some reason it reminds me of a collection plate (not that that is a bad thing! :) ). Is the wood really that dark? Or did you stain it?

Scott

Re: Quick, one hour plate in curly white oak

#5

Re: Quick, one hour plate in curly white oak

fgvanatta

Very nice. I especially like the gold leaf accent.

Frank

Re: Quick, one hour plate in curly white oak

#6

Steven Antonucci

No stain

Steven Antonucci

It's natural, but I think the darkness is the figure. It's pretty blond, but then I lost the chatoyance in the pics...

Steve

Re: Quick, one hour plate in curly white oak

#7

Ellis Walentine

Very nice, Steve

Ellis Walentine

I'd like to know the best way to turn plates quickly, as I need a bunch of them myself. Short of making one of those Longworth chucks, is there a good way to quickly and effectively chuck flat boards for turning plates? How do you do it?

Ellis

Re: Quick, one hour plate in curly white oak

#8

Steven Antonucci

Method of work

Steven Antonucci

For starters, the wood is anything but flat. Most of the boards came out of a kiln case hardened and distorted.

My approach to making these quickly is pretty straightforward. I start between center with a bandsawn disk of wood. I do a quick flattening of both sides using pull cuts from the face until I am 90% flat. Decide front and back, and then turn a very small tenon on the back (1/8"). Maybe 15 minutes.

Once it is in the chuck, it's all finish cuts and details. By making those cuts cleanly with sharp tools, I started sanding at 180, 220, 400 (couldn't find 320) and I had the entire face and 80% of the back done. I reversed it in a second chuck which has cole jaws in it to finish off the tenon and finish sand. I put some newspaper (a few sheets) in between the plate and the cole jaws to protect and cushion the leafing. Finish turning: 15 minutes. Sanding: maybe 5-10 minutes. Leafing: maybe 10 minutes. Finish: maybe 10 minutes over 4 hours.

As this is going to a gallery (for sale), I didn't want to invest 4 hours into a piece that will probably sell for $50-75. I will see how it does, and then if the gallery requests more like it, I know I can make them fast enough to justify that cost. While I am happy with the results, I think if I had to make 5 of them, I could do it in about 3 hours...

Steve

Re: Quick, one hour plate in curly white oak

#9

Ellis, my method

Jorge Casta�eda

is to use a faceplate with a glue block. Once mounted you can turn both sides, then to the vac chuck to clean the bottom. I use an adapter to mount the faceplate in the tailstock, sever and fire the vac.

Works great for me

Jorge

Re: Quick, one hour plate in curly white oak

#10

Another Way....

Barry Irby

My Cole jaws only expand to about 10". Did not want to pay for the jumbo set and I am not sure they existed at the time. I got a piece of flat steel bar 1" wide and about a 1/16" thick. 1/8" thick might be better. Cut the 36" long piece into 8 pieces about 4 1/2" long. Round and smooth the ends. Bend about 1" past 90 degrees to form an elongated "L". Drill a hole in the long end spaced accurately from the base of the bend. The hole is big enough to accept the screws that hold the rubber bumpers on the Cole jaws. I dipped the L end in black rubber made for coating tool handles, but I am not sure that's necessary. You mount them on the Cole jaws to extend out past the edge of the plate. Turned my 10" jaws into 16" jaws. I use them a lot. They hold better than the rubber bumpers and I use them for things that are as small as they will go. I made these years ago and they get a lot of use. The work can ride on the rubber bumpers or you can just use the screws and cover the heads to protect the work.

Cut the disk, mount it between centers and turn the rim. Then mount it on the Cole Jaws plus the hooks and finish both sides. You can flip back and forth and don't have the centering problems you might with a vacuum chuck. You can also mount square pieces or rectangular pieces.

I can post a picture if anyone cares.

Re: Quick, one hour plate in curly white oak

#11

Steven Antonucci

I might have to make a set of those...

Steven Antonucci

FYI- if you start between centers, when you reverse the plate, you have a center mark on the backside to use the tailstock to recenter. No fussing.

I have a buddy who was making round cheese boards for Xmas and I gave him the epiphany to run them through the jointer before the were on the lathe. He ended up just turning them round and making a quick bead or groove on the lathe...

Steve

Re: Quick, one hour plate in curly white oak

#12

Ellis Walentine

Thanks for the advice

Ellis Walentine

If I could ever get away from the computer, I'm going to give a couple of these ideas a try. Before my shop fire, I had a set of Cole jaws for my Stronghold chuck. That hasn't been an option since then.

Steve, if you turn a spigot on the bottom, does that mean you have to start with 5/4 or 6/4 stock?

Ellis

Re: Quick, one hour plate in curly white oak

#13

Re: Quick, one hour plate in curly white oak

Mike Foster

Hey Steve that's a Very nice one hour plate. I have been away for a while and just started picking up some of the threads. How did you do the leafing so fast? Leafing is another technique that is high on my list to learn and experiment with.

Mike

Re: Quick, one hour plate in curly white oak

#14

Re: Thanks for the advice

Jorge Casta�eda

Ellis, Yes stop for a bit and go get a byte, and steal to the shop and turn.

Here is a picture of my method:


I don't have a picture of the reverse mounting to the vacuum chuck, but here is one of the Oneway live center with the adapter that allows you to mount the faceplae in the tailsatock, snugg it to the vac chuck and spin it, now start the severing, but before it is completed, stop the lathe and fire the vac, finish severing with a saw, I use a ryobi, and you are in your merry way, it took me longer to type this than what actually takes to clean the foot.


Hope this helps

Jorge

Re: Quick, one hour plate in curly white oak

#15

Steven Antonucci

Might be 5/4, but it isn't 6/4

Steven Antonucci

The lumber was sold to me as 4/4, but some of it is 5/4 for sure.

By starting between centers, all of the hard cutting is done when I make that small tenon. I doubt it's even an 1/8", but in white oak, that's plenty. Tailstock in place until the final pass and cleanup of the nub on both sides.

Here is a shot of a small section of the lumber pile that this came from.


If you look at the board on edge, you'll notice it's got some problems. :-) I've certainly learned to cut around defects with this lumber, and I only have another 400 BF or so to go...

Steve

Re: Quick, one hour plate in curly white oak

#16

Steven Antonucci

Leafing is far from perfect

Steven Antonucci

I had finish sanded the band and then applied the sizing. It takes a couple of minutes to set up, but I didn't count that against my hour since I was working on something else while it tacked up.

As far as applying it, I just stick it on. It's not a flawless, filled pore surface, but it's good enough for what i wanted it to look like. If I wanted that flawless surface, I might have gessoed the pores and sanded that to a higher grit before applying leaf. I cleaned it up the edges with a detail gouge and a quick touch up on the sanding...

Done.

S