Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

table glue up

Posts

table glue up

#1

table glue up

john lucas

I finally got the table glued up. What a hassle. After assembling the top which had the 24 spindles I decided it was too risky to glue it up by putting glue in the one side and glueing all the spindles, then trying to put the other side in. If anything didn't align perfectly I would be screwed.

I decided the best course of action was to mix up epoxy with thickener to the consistency of peanut butter so it would not run. Then I could epoxy the top and the ring and put all the spindles in. That would give me a fudge factor if anything didn't align just right.

It actually went better than the dry runs because the epoxy was a little slippery which made sliding the spindles in the holes easier.

I had to weight one side of the bottom glue up because I couldn't get clamps on the workbench side.

That was a load off my mind. Now I just need to screw the bottom to it's brace and the top to it's braces and I'll be done. No actually I have to apply some more finish to the top. I had 4 layers of finish on the top before I could see some little swirl scratches that had to be from the first grit. Bummer. I looked hard for those things. Anyway I sanded off the old finish and started over. It looks better now but needs about 3 more coats on the top.

Actually there one more thing. That dreaded leveling of the legs. It may be 6" shorter by the time I get that done. :D

Re: table glue up

#2

Re: table glue up

Barry Irby

John, Good looking so far.

I have a method of leveling tables that works well for me.

I have a router mounted on the wing of my TS. I think the key here is that he router table is big enough for the table you are building to sit on. The router table is flat. (Well, flatter than the floor)

Put a straight bit in the router and raise it about a 1/32" above the table. Make the projection of the bit the same as a thin piece of wood or veneer about the size of a credit card. (I use one of those motel room key cards.) Set your table on the router table and figure out which is the long leg or which two are longer. Slide the longer legs back and forth on the router. (You need a fairly small hole in the table for this, so an insert may be necessary.) Route away about half the leg. Insert the card under that half to shim the leg. Route away the other half. Repeat as often as necessary to shorten the leg the correct amount. Goes very quickly once you get the knack. Also keeps the cut "square with the world" so that the leg will sit flat on the floor.

Re: table glue up

#3

Re: table glue up

John K Jordan

That sure looks like a time-consuming project! I thought people liked woodturning since they could finish things very quickly.

Just wondering about the epoxy thickener - is this something you bought? Years ago I bought special epoxy paste that was so thick you could have stuck a blob on the ceiling and it would have hardened like that.

JKJ

Re: table glue up

#4

Re: table glue up

John Lucas

John West Systems sells 3 thickeners. I'm still learning to work with it. I haven't run a test on making really thick stuff yet. I thought I did but it becomes a little more viscous at one point during the curing and the stuff sagged. I'm going to try and mix some up to a clay like consistency like Marilyn Campbell does. I don't want to copy her work but I do want to learn the process to see how I might use it. It takes a lot of the thickener to make it thick. I used 3 or 4 teaspoons for 2 ounces epoxy and it still started out about a little less thick than toothpaste, then it sagged more as it dried.

The one thing I don't like about the thickeners they sell is they change the color from clear to either white or tan. I may try adding some colorant to change the color.