Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Powermatic arbor replacement

Posts

Powermatic arbor replacement

#1

Powermatic arbor replacement

Mac Ray

A friend of mine chewed up the threads on his 3520B arbor.He was told by Powermatic that it would take at least 4 to 6 weeks to get a replacement...........anyone know where he might get one sooner? Maybe a Powermatic dealer or ?................... thanks

Re: Powermatic arbor replacement

#2

Re: Powermatic arbor replacement

Dave (PacNW)

Try Equipment sales and surplus in Auburn, WA. Talk to Frank and see if he can help http://www.equipmentsalesandsurplus.com/

Dave (PacNW)

Re: Powermatic arbor replacement

#3

Re: Powermatic arbor replacement

Mac Ray

Thanks,I'll pass that information on......

Re: Powermatic arbor replacement

#4

Re: Powermatic arbor replacement *LINK*

john lucas

Check with General Industrial. They sell rebuilt Jet and Powermatic equipment and may have parts for them.


http://generalindustrial.com/

Re: Powermatic arbor replacement

#5

Re: Powermatic arbor replacement

Barry Irby

Wonder if a machinist could build up the shaft and re-turn the threads on it? Even if they could would that be faster/cheaper/as good?

Re: Powermatic arbor replacement

#6

Re: Powermatic arbor replacement

John Lucas

Barry One of the reasons I bought the powermatic was because everything on the machine could be rebuilt or replaced by a good machinist. That would include re-threading the spindle or even re-building the spindle.

I can't imagine that the threads would be so messed up that they wouldn't be useable. Take a V file and clean up any areas that stick out. Dent's below the surface should not hurt the operation of the lathe. As long as the chuck or faceplate will screw on easily and bottom out against the back flange the everything should work. Now if the spindle is bent that's a different ball of wax.

Re: Powermatic arbor replacement

#7

Re: Powermatic arbor replacement

Mac Ray

It seems that the boys had a bit of a problem when they put the faceplate on the arbor....it was attached to a 4' glued up disc mounted on plywood and they got it cross threaded...pushed their luck a bit too far and then couldn't back it off either.Even a machine shop couldn't remove it....the spindle suffered quite a bit during all this and the bearings seem to have a headache also....................along with the spindle lock and the index lock...looks like all new parts are in order,in the meantime,looks like I am going to turn the mirror frame for them...am mounting it up tomorrow on my OW and hope I have better luck,it will take two of us to get it onto the lathe........maybe I will take a pic of it when it's done.......this is the first of many that they have to do,so I'll do the first one and hope they get their lathe up and running soon.....thanks all for the sources for parts,I sent them on .....

Re: Powermatic arbor replacement

#8

Re: Powermatic arbor replacement

Dave Peebles Lyons, Ohio

Hi Mac,

Boy, that is a bummer. Is that spindle not hardened? Those must have been some stong guys to mess the spindle up that bad. You would think the spindle would win out over any faceplate.

Hope all is well with you,

Dave

Re: Powermatic arbor replacement

#9

Re: Powermatic arbor replacement

Mac Ray

I Dave,been a while hasn't it? The faceplate won because it had a four foot diameter,150# blank attached to it.....1/4 turn too far lifted a chip I think,we wont know till we get the faceplate cut off the shaft.........I think it was a learning experience..........hope so.........

Re: Powermatic arbor replacement

#10

Re: Powermatic arbor replacement

john lucas

Dave Lathe drive spindles are actually kind of fragile. They are hollow and when you measure the thickness at the bottom of the thread there isn't very much metal there. Don't forget the widest part of the Morse taper is in the threaded area. The rest of the shaft is usually bored to a little larger than 3/8 so it's fairly strong back where the bearings are.

I had to replace the spindle on the first used lathe I had because it was bent. It was 1"x8. I had a machinist friend make me one with 1 1/4"x8. It's much thicker but still pretty fragile. I don't have the specs in front of me but the fat end of a #2 morse taper is about 3/4" and the bottom of a 1"x8 thread is closer to 7/8" so you have a wall thickness of about 1/16" at the thinnest point. I've seen other lathes with bent spindles. That's why the tailstock is so important on large long turnings.

some of the early lathes like Powermatic and I believe Conover had 1 1/2" spindles.

Re: Powermatic arbor replacement

#11

Re: Powermatic arbor replacement

Roy Girolami------WebKitFormBoundary9yANUT8mn8C+Zo

Mac, when I got my 3520A. there was a spindle thread issue. The spindle outer diameter in the threaded part was a tiny bit oversize, so aftermarket chucks wouldn't fit. i went through a back and forth and finally got a spindle that worked. The short answer is i have 5 spindles with various over/undersized places. They are not used, but would need some attention by a machinist. Let me know if you would like to try one on for size.

Roy Girolami

Re: Powermatic arbor replacement

#12

Re: Powermatic arbor replacement

Mac Ray

Thank you very much for the offer of help, I will see by friend who has the problem on Monday and will tell him about this...will get back to you........thanks....Mac

Re: Powermatic arbor replacement

#13

Keith Tompkins

Re: Powermatic arbor replacement

Keith Tompkins

Hey John, If I screw up the threads on my General, I can just turn outboard. Kinda like having an extra lathe :D

Re: Powermatic arbor replacement

#14

Re: Powermatic arbor replacement

Mac Ray

Hi Roy,How do we get in contact with you?

Re: Powermatic arbor replacement

#15

Re: Powermatic arbor replacement

Dave Peebles Lyons, Ohio

Hi Mac,

Thanks, that makes sense to me. Hope you get it all fixed up. Sounds like you have a couple of options from reading this thread.

Maybe I'll see you at an Indyfest in the not to distant future.

Best wishes,

Dave

Re: Powermatic arbor replacement

#16

Re: Powermatic arbor replacement

Dave Peebles Lyons, Ohio

Hi John,

Thanks for explaining that to me. Maybe one day I will buy one of those spinny things so I will understand better. :)

Dave

Re: Powermatic arbor replacement

#17

Re: Powermatic arbor replacement

Mac Ray

Roy,My e-mail is wdwork@midcoast.com if you would like to part with one.....drop me a note,we'll talk...............

Re: Powermatic arbor replacement

#18

Re: Powermatic arbor replacement

Roy Girolami------WebKitFormBoundary9yANUT8mn8C+Zo

Mac, I sent you an e-mail yesterday.

Roy

Re: Powermatic arbor replacement

#19

Re: Powermatic arbor replacement

Mac Ray

Hi Roy,sent you a message today at Marthas e-mail address...thanks