Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Turning Wet

Posts

Turning Wet

#1

Turning Wet

Fred Bearman (Port Huron, Michigan)

My turning experience has been with pretty dry pieces of wood. Now I see very pretty pieces of wood out there and have purchased several, as I am bound and determined not to let my disabilities keep me from turning at all. The blanks that I have purchased include a a 5 x 5 x 5 block of Moluccan Ebony, with a stated moisture content of 39%, a 6 x 6 x 11 block of Ambrosia Maple with MC of 32%, and an 8 x 8 x 3 blank of Ambrosia Maple with a MC of 29%. All are heavily waxed (which is another new twist for me). Two of these are slated for hollow forms, while the third will be probably be a bowl. I have read about the various drying methods (DNA, boiling, and leaving in a paper bag forever), and I am unsure as to the best approach to these - do I rough turn and then use one of the above drying methods, or do I plan on turning to completion followed directly by sanding and finishing? I guess that spending actual money for these blanks has me feeling a wee bit timid. Any help or advice would be most welcome. Also, none of these blanks contain the pith.

Re: Turning Wet

#2

Brad Vietje

Re: Turning Wet

Brad Vietje

Fred,

Have you already learned how to turn hollow forms? I would advise not learning on expensive wood -- not even the drying and finishing parts.

If you live in an area with Maple or Cherry trees, or other species of decent turning woods, try to find some free or really cheap wood to work out the issues. Around here - admittedly more rural than most of the US -- I can go to the town highway department and get some tree trunks that were removed after big storms, or removed for road maintenance. Many towns and cities in the Northeast have a "stump dump" or a log pile at the forest and parks department, or even at the "transfer station" or recycling center.

Other areas will certainly be different, but a few minutes calling around and asking your road commissioner (Highway dept.) or recreation department might net you some free practice wood.

In turning green wood you have two basic choices:

1. Turn to completion while green and either wet sand or dry the wood just enough to sand and finish it. Thin walls and base will reduce chances of checking badly. They should warp a little out of round, but not crack.

2. Rough out, air dry, complete when piece stops losing weight. End piece is round, and should stay that way.

I do both, but usually wet turn burls or highly figured wood so I can get a textured final result, and I part turn - dry - and re-turn straight grained pieces or show pieces that I want to be round or shiny or both.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Turning Wet

#3

Re: Turning Wet

Mike Jones in Redding, Ca

Fred,

Lake Huron, Michigan has 90% humidity at just 24 degrees and clear skies tonight. With conditions like these, you will not likely experience any rapid moisture loss (which causes our problems) from your turned forms.

Further, closed forms, like your hollow vessels, tend to fare better than open bowl forms, so with an 8 x 8 x 3, I would I would rough out the bowl and weigh it often until I found for sure that it was not losing weight too fast.

just my .02

Re: Turning Wet

#4

Re: Turning Wet

Fred Bearman (Port Huron, Michigan)

That was pretty much what I was thinking, thanks for your input.

Re: Turning Wet

#5

Re: Turning Wet

Fred Bearman (Port Huron, Michigan)

I have done small hollow forms with success. I am pretty limited in obtaining wood other than purchasing through retail outlets, as I have difficulties in handling anything much larger than these pieces to cut blanks from.

Thanks for your really good input.

Fred

Re: Turning Wet

#6

Re: Turning Wet *LINK*

John Jordan

Take a look at my website, and the article "Understanding Green Wood". It's not terribly complicated unless you make it so. :) Good luck.

John


http://www.johnjordanwoodturning.com

Re: Turning Wet

#7

Re: Turning Wet

Fred Bearman (Port Huron, Michigan)

Hi John,

Thanks for the link with the good information. A lot of my problem is that I overthink most every thing that I do :) . Your beautiful vessels certainly attest to your knowledge of the subject.

Thanks again.

Fred