Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Just Getting Started

Posts

Just Getting Started

#1

Just Getting Started

Paul Storck

I'm interested in learning about turning. Taken a class at the local Woodcraft store. Thinking about buying a lathe for turning table legs, spindles, bowls, knobs etc. strictly as a hobby. What specifications should I look for in a "starter" lathe. Thanks for your advice.

Paul

Re: Just Getting Started

#2

Re: Just Getting Started

john lucas

Paul If you want to turn table legs then it needs to be at least 32" between centers but that's with the drive center and live center installed. 34 to 36" would be better. For bowls, bigger is better. 12" swing or bigger is better. 1 horsepower or more. Many lathes came with 12" swing and 3/4horse motors and that will work.

don't buy one of the really cheap lathes. They are junk and just ruin the turning experience. My recommendation for a good starter lathe is one of the mini lathes. The Jet, Delta, Rikon or Grizzly 12" swing versions are great. Make sure it will take a bed extension and you will be able to step up to turn table legs. They will let you do an awful lot of work and get used to turning. Then later you can step up to a bigger lathe. The mini lathes have good resale value.

Re: Just Getting Started

#3

Re: Just Getting Started

John Scheideman

John's suggestion of a mini-lathe is a good one. I would also suggest that you look at a larger used lathe. There are many good ones around. People are always upgrading and selling their old lathes. If you really get hooked on woodturning you may outgrow a mini-lathe quicker that you think. As John mentioned, make sure you buy one with at least a 3/4 hp motor.

John

Re: Just Getting Started

#4

JL

Determine a budget!

JL

You've got many options - it all depends on how much you are willing to spend.

You will require turning tools and a means of sharpening them. Those are a given. Your choices can be as expensive or as inexpensive as you want to make them. Ditto for lathes.

A) Turning tools - sets from $150-450.

B) Grinder - preferably an 8" - $100-200

C) Grinding jig - home made to a Oneway Wolverine and Vari-grind - $10-170

Finally lathes - you could go for a starter lathe. That works quite nicely. In my opinion the following features are desirable - especially for turning a variety of things.

1) Electronic variable speed - turning a knob to vary the speed is really a nice thing.

2) Power - at least 3/4 hp. Preferably more. You may not need 1.5 hp - but it is nice to have it :) .

3) Bed extensions - you can't turn a leg on a short lathe - unless you want to do it in pieces.

4) Large swing or "throw" - If you want to turn platters, you can't do it very well on a lathe with a 10" swing. So figure on going for at least 12".

A lathe like the Nova 16/24-44 is nice - but you will have to change the belt. My personal preferences would be either the Delta 46-460 or the Jet 12-20 VS. There are other good lathes out there. The nice thing about the Jet mini lathes are that they do retain value. The Delta would probably retain value also.

My $0.02.

Re: Just Getting Started

#5

Steven Antonucci

So many ways to answer this

Steven Antonucci

A good mini is certainly an option. And you can make or buy an extension if you need to go longer for spindles. A buddy of mine made one for turning baseball bats. Works well enough in that type of work.

If I wasn't sure what my true intentions with turning were, I would probably do something like this or pick up a used lathe that was bigger. Either way, you probably end up about the same $$$ and having to make stuff for it to work in the varied items you describe. $300-400 invested, likely returns $300-400 if you decide this isn't what you want to do. If you buy junk, you are usually stuck with it or 50 % of your cost.

I would also encourage you to buy 3-4 tools and work at them. Most turners have way too many tools (my hand is up). Until you can use them, it doesn't make sense to buy more. Having a chuck solve a lot of hard problems quickly. There are some inexpensive chucks on the market, and they work well enough for what you describe. $200 should get you started.

If you've never turned, find a local AAW chapter and join it. Might cost you $25, but it's a great investment.

S

Re: Just Getting Started

#6

Re: Just Getting Started

Don Evans

Paul:

If you can contain your excitement for a little bit, my advise would be to contact the Woodcraft store again and find out about joining the local turning club. I'm willing to bet that if there is a Woodcraft local there is at least one club maybe more.

Why do this, if the club is like all the one's I've known you'll have NO trouble visiting members shops and actually try out many different types of machines. You'll learn enough quickly to make a much more informed decision on what you want.

It will boil down mostly to your particular budget at this time.

I'm a firm believer in variable speed from a safety plus better working experience.

Also there is a mentality about larger lathes that in reality just doesn't pan out especially in the beginning. I would be willing to bet that 99.8 percent of the turners on this forum very seldom, if ever, turn anything that needs more than a 12" lathe.

Now the bigger iron has many advantages other than size. So if you have unlimited budget go for one. I've got a Oneway 2436 but I've never turned anything over 10" diameter on it.

Don

Re: Just Getting Started

#7

Re: Just Getting Started

Paul Storck

To all who have responded to my getting started question,

One thing I can always count on is that when I post a question on Wood Central, guys like you will provide well thought out opinions and suggestions. Thanks for all your ideas. I think the suggestion about joining a local turning club will present me with even more information about the ins and outs of various models and features. It's a lot to think about and I think I'm on the right track. Thanks again.

Paul