Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

A question on Demo's

Posts

A question on Demo's

#1

A question on Demo's

John Lucas

>My Demo's tend to be skill oriented. By that I mean I try to teach how to do things, How to use the tools better, and little tricks that have made turning easier or more efficient. I don't always finish a project that can be donated to the club. This is due to several reasons, either need a tool that you don't always have, such as a drill press, or you have to spend to much time cutting or hollowing and I feel that time is better spend discussing how to use the tool better or sharpening or some other technique.

Some projects like my angels or christmas ornaments or even hand mirrors if I leave out some of the skew part of the demo. Some demo's such as tool making obviously aren't designed for finished product.

I've started wondering if a demo should always be a project that most people in the club could build or should it be what I'm doing now. I feel what I do now helps the more advanced turners so they aren't bored by a simple project but may not give step by step instructions in minute detail so the novice can complete the project.

What do you all think. You've sat through a lot of demo's.

Re: A question on Demo's

#2

Re: A question on Demo's

Roger

>John,

In the few demo's that I've done I've had pieces in various stages of completion for the folks to see. With a hollowform for instance, I'll have a rough blank, a piece with only the outside turned, another with the hollowing done and a totally finished piece in case I screw up the main one I'm working on. You can grab any one of the partially turned pieces and carry on with it, as far as time and attention allow. You should have time this way to touch on sharpening, tool presentation, sanding etc. This works for demo's to other turners. The general public will probably want something quick and simple. That's just my opinion, I'm sure there are lots of others out there.

Roger

Re: A question on Demo's

#3

Re: A question on Demo's

Scott in Falcon

>Personally, I like demos of all types. I enjoy the step by step project type demos. I enjoy the demos where a presenter has brought in pieces at various stages of a project to save time. And I like the technique demos as well.

I think that the important thing is to label the demo appropriately. If the demo is focused on turning techniques, rather than a specific project, then this should clearly stated in the description of the demo. I don't think that disappointment occurs because a demo is one type or another. It occurs when a spectator arrives with a set of preconcieved notions about what they expect to see and then those expectations are not met.

Scott

Re: A question on Demo's

#4

Re: A question on Demo's

Carol Reed

>Another thing to consider. You have been doing demo's a while. You are a known commodity. You will be asked to do a demo based on what folks think you will be doing. You cannot be everything to everyone - though you have an amazing set of skills that transcends most people!

So if the demo is where you ma be new to the group, stick with what people may expect of you. If you are doing one for the home club, bill it as something new for John Lucas and have fun doing it.

Do bill it, label, describe, market it accurately so folks know what they are getting before they arrive. Offer to have them bring in a tool or a project they may have a question with that dovetails into your demo. That is a most helpful way to get them involved.

You are a great teacher, John. I remember your instruction at Indy Fest a few years ago. I learned lots even if I couldn't go back and practice what I learned.

BTW, if there is an Indy Fest this year, I hope you can be there. I plan to be there and at this time in my life I do have time to practice what you have to teach.

Re: A question on Demo's

#5

Re: A question on Demo's

Jim Shaver

>My turning demo's are mostly pen making, so it's easy to finish a project from Eh-to-Zed in about 30 min if prepared. But I also find that a lot of people want to learn the details, not the whole project.

In the turning world you can complete many items in a short period of time, in furniture making it can take days or weeks. I my self enjoy learning how to use a tool or technique most, but I think my learning curve is advanced to that point, it all depends on the skill level of your audience in my mind

Re: A question on Demo's

#6

Re: A question on Demo's

John Lucas

>Jim That's it. I'll do a furniture demo that takes 3 weeks to complete so they have to hire me for about 15 evenings. Plus I get to stay and actually see what town I'm visiting instead of zooming in and back out in about 4 hours. Sounds like a solution to me. :)

Re: A question on Demo's

#7

Re: A question on Demo's

John Lucas

>Thanks Roger. I do that on some demo's because it's simple impossible to show them how to do the various stages of a project. After all no one wants to wait for glue to dry on a project that requires assembly.

Re: A question on Demo's

#8

thanks Scott- labeling is important

John Lucas

Re: A question on Demo's

#9

I'll have to check on Indy Fest

John Lucas

Re: A question on Demo's

#10

Re: A question on Demo's

Russ Fairfield

>A demonstration can focus on entertainment, showing off your personal skills, or teaching them something they can use. Any one of those can make for a good demonstration; but a great demonstration is the one that does all three because there is something there for everybody.

Although there are many demponstrations where nothing is made, most clubs appreciate the demonstrator leaving something behind because they have a collection for display or they want something they can raffle off to increase their treasury. You will avoid hurt feelings by asking ahead of time, and bringing a completed piece to donate to them if they expect that.

Re: A question on Demo's

#11

Steven Antonucci

My demo's have all been "free"

Steven Antonucci

>so they get what they get. If I was being paid, I might have a little bit more of a planned syllabus, but probably not.

Here is why:

Anything that I have ever demonstrated has been so broad of a topic that I like to have the flexibility to adapt to my audience. If I was discussing a topic like hollowing with a group that had never hollowed, I would focus less on completing a vessel than what was required to complete a vessel. If the group had some experience, I might cover more advanced topics like undercutting or hollwoing with a bowl gouge.

In the event that the group needs to get a completed project out of the demo, they've hired the wrong guy (me) for that meeting.

S

Re: A question on Demo's

#12

Mike Stafford

Re: A question on Demo's

Mike Stafford

>I always contribute something to the club for them to raffle. I also always bring a gift for my host and hostess.

I am honored to be asked to do a demonstration and the best way for me to express my gratitude is to contribute something to the club.

Usually I bring gifts to members who I have corresponded with or who have been kind enough to share wood or expertise with me.

Re: A question on Demo's

#13

Re: A question on Demo's

Bill Turpin in WNC mountains

>I have been amazed by how much unfinished and unsigned demo pieces will bring at the club auction. Our club which has � 10 demos a year by known turners raises more than $2K/yearly from the demo pieces. There are several members who have volunteered to finish demo pieces so that they will bring more $.

I think the demonstrator's handbooks being done by some symposiums (Greenboro, NC for one) are wonderful. I think that all demonstrations should include some kind of handout: supplier links, grind profiles, wood sources, special tools, etc. The expense should be discussed with the clubs and be included in the fee.

I especially like the demos where the teachers are REALLY prepared. Multiples of prepared blanks for the start, and the major steps towards the end. Who really wants to watch someone rough a blank to round.

I do not like the thirty to 45 minute slide shows to start the demo. Five minutes is fine, but not much longer.

Bill

Re: A question on Demo's

#14

Re: A question on Demo's

E Tabachek

>I want my demos at club meetings to be short, 30 to 45 minutes. More of an overview of the technique with lots of time for questions and for the "know-it-all" members to tell us how to do it better. These demos are not meant to be complete teaching / learning sessions. Those are reserved for hands - on classes and seminars when students pay for the opportunity to learn. By the time the meeting schedule gets around to "The Demo" members are looking forward to going home or to the after meeting session at the coffee shop.

OTOH, another member of our club who often demos has the opposite view. His demos include everything (all the steps) from start to finish, someting that bores many members so they slowly break away into little groups. I am not certain that most members remember much of what is shown any way.

ET

A club demo that lasts an hour is a long demo that usually involves a lot of tedious work when members loose interest.

Re: A question on Demo's

#15

Keith Tompkins

Re: A question on Demo's

Keith Tompkins

>Hi John, I took guitar lessons when I was a bit younger...I made the mistake of asking the instructor the chords to a favorite song. His reply.."Learn to play your instrument, then you can play any song you want!" I feel that way about turning...learn proper skills, then turn anything you want. Anything. Like you, I don't usually focus on a finished product. Most of my demos focus on design concepts...I feel this is the area where most turners are weak, and where my experience can be the most beneficial. Hey, you've seen one of my demos! Anyway, understanding good design can lead to big improvements, no matter what type of pieces you turn. I think "project" demos can become very boring if the demonstrator isn't very organized and able to keep the pace up. Too many people get hung up on details, and ruin an otherwise good presentation. In Hartford, I'll be doing two demos: Ten essential cuts, and Design for beginners. Neither will have projects, but will be filled with lots of useful stuff.

Re: A question on Demo's

#16

Re: A question on Demo's

Jennifer@Indy.USA

>Wanna come demo here and stay at our house :D

Re: A question on Demo's

#17

Re: A question on Demo's

Bill Turpin in WNC mountains

>The schedule for our (www.carolinamountainwoodturners.org)club starts at 10 AM on Saturday with business. Demo starts at about 10:30 AM, goes until noon. Lunch until 12:45 when instant gallery starts. Demo starts at 1 PM and lasts until about 4 PM. This gives our world class demonstrators time to complete about three projects. Our meetings rival many symposiums with 4.5 hours for the demo. The demo budget for 2010 is $5500.This year we will have: Soren Berger, Alan Lacer, Trent Bosch, Alain Mallard, Nick Cook, Hans Weissflog, and George Hatfield. Come join us. All demos are open to public and FREE. We meet in a 400 seat auditorium, we have room for all visitors.

Bill in WNC mountains

Re: A question on Demo's

#18

I need a Design Demo

Paul Zerjay

>Too bad I'm Broke!! ;)

Re: A question on Demo's

#19

Re: A question on Demo's

Charlie Anderson

>When John Benton demoed at our club, his took his demo piece home with him and finished it. And by finished, I mean sanded, oiled, mounted for display on a stand with the stand inscribed.

That was nice, by way above and beyond the call.....

Re: A question on Demo's

#20

Mike Stafford

Re: A question on Demo's

Mike Stafford

>Do you have room for more of my junk????

It only seems proper to thank your host/hostess.

Re: A question on Demo's

#21

Re: A question on Demo's

john lucas

>Jennifer I would love to but I need to wait and see what's happening with my job. There are going to be some layoffs and I'm pretty sure I'm at least on the short list. That's going to really change my life if it happens so I'm trying to hold off on too many plans right now. I have relatives in Indianapolis and would like to visit them also.

Re: A question on Demo's

#22

Re: A question on Demo's

john lucas

>I've been dying to visit your group and probably will one of these days. You certainly have some great people this year.

Re: A question on Demo's

#23

Re: I need a Design Demo

john lucas

>Well if you can make it down to Tennessee I'll put you up for the weekend and we can play in the shop. That should take care of the broke part. Been there done that. Hey wait, I'm still there.

Re: A question on Demo's

#24

Re: A question on Demo's

Vince Welch

>Hi John,

While you may not be able to please all the people all the time I beleive there is value in asking or getting feedback if possible before the demo as to what it is the club or audience would like to see. Perhaps give them 2 or 3 options. in addition, this may also provide you feedback as to what people have come to know you for. Vince

Re: A question on Demo's

#25

Re: A question on Demo's

Bill Grumbine (Kutztown PA)

>Speaking from the other side of the demo lathe...

I almost always ask what it is the club would like to see demonstrated. The only times I don't is when someone writes or calls and says, "We would like to see you demo __________ ". I will discuss choices based on how the club is composed, but for the most part I try to do something that will appeal to everyone for at least a little while. For the most part, more advanced turners are not going to be hugely interested in seeing a simple bowl. Beginners may be intimidated by the whirling wings of a winged bowl. My main goal is to demystify the process as much as possible for those who are attending. Well, that and cover as many people as I can with shavings. :D People at TSS last September reported that they were asked if they had taken part in the actual turning after they exited my rotation a couple of times.

I often leave an uncompleted piece. Sometimes it is even pretty rough looking. I am not there to show people how well I can make something, although once in a while it comes out looking okay. They already suspect that I know a little bit about finishing and sanding and such. I am there to show a process, answer questions, tell stories, and pick on the engineers in the audience.

One of the most valuable feedback devices you can use is to observe how many people come back after lunch. ;)