Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

pen vise, PSI Woodworking

Posts

pen vise, PSI Woodworking

#1

pen vise, PSI Woodworking

John K Jordan

>Anyone use the DRILLCENT3 pen blank vise from PSI Woodworking? I bought one a few years ago and only used it occasionally.



It worked fine for a while then began to get sloppy and lose it's center often. Examination showed the small threaded center rod was not threaded tightly into the vice jaw. I tightened the rod by hand and tightened the lock nut but it quickly loosened again. Closer examination showed the threads in the aluminum vice jaw appeared to be stripping. The threaded rod itself appeared to have a significant taper ground on the end allowing only one thread to engage before the end bottomed out. Seems like a design flaw to rely on one thread in soft aluminum.

Since PSI will only fix it if under warranty (and I have no idea where the receipt is), I repaired it by grinding away most of the taper on the small threaded shaft so more than one thread will engage in the soft aluminum jaw and tightened it securely.

Anyone have this vise and have similar problems? If so, was there a permanent fix?

JKJ

Re: pen vise, PSI Woodworking

#2

Re: pen vise, PSI Woodworking

Cyril Griesbach

>John, I have one like that and if memory serves, and it doesn't always, I believe I got it from Craft Supplies. I have not had any problems like you describe. The next time I can get out in the shop I'll check mine....if I can remember. :D

Re: pen vise, PSI Woodworking

#3

Re: pen vise, PSI Woodworking

Scott Greaves in Blackfoot ID

>Hi John!

A lot of people have problems with that PSI vise. I have not heard of anyone who has come up with a fix for it.

If you like this centering style of vise, get the one by Paul Huffman. For details visit the IAP and do a search on Paul's Vise.

Scott.

Re: pen vise, PSI Woodworking

#4

Re: pen vise, PSI Woodworking

adrien

>Islamic Association for Palestine

Intra-Abdominal Pressure

??I tried. No idea what or where IAP is.....

Re: pen vise, PSI Woodworking

#5

Re: pen vise, PSI Woodworking

Fred Bearman (Port Huron, Michigan)

>IAP = International Association of Penturners (www.penturners.org)

Re: pen vise, PSI Woodworking

#6

PSI's and Paul's

John K Jordan

>Scott,

Thanks, by coincidence I signed up on the IAP site earlier today. I've been making pens lately so I figured it wouldn't hurt!

The fix I did made it much stronger - after previously struggling with it for some time I drilled a couple of dozen blanks today with no problem. I have an idea for an even better for a permanent fix which involves a left-hand threaded nut, a small steel plate, and my welding machine!

But if I can get one of Paul's vises, I probably wouldn't bother - it looks great and I love the idea of the open front access. Do you know how to get in touch with him? I found lots of threads talking about the vise, pictures and all, but when I found Paul's profile I couldn't see an email address anywhere. Do I have to wait a bit after joining to access email addresses?

JKJ

Re: pen vise, PSI Woodworking

#7

Re: pen vise, PSI Woodworking

Jim Shaver

>I drill on the lathe, so simple, so easy.... :)

Re: pen vise, PSI Woodworking

#8

Re: pen vise, PSI Woodworking

Galen Vetterick

>Not sure I follow all your description and do not have one to compare but for stripped threads in aluminum just drill out and put a brass or steel thread insert in so you run threads on stronger insert materials.

Too fancy for me I had just cut vees in an old 4" wood handscrew clamp and center it under the drill press.