Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Need a home made "outboard" Turning solution.

Posts

Need a home made "outboard" Turning solution.

#1

Need a home made "outboard" Turning solution.

mamc

>Least I think it is called outboard turning.

I have a cheapo Home depot lathe ( perfectly matched to my intermediate,maybe turning skills).

It only does a 12" diameter.

I has treated me well allowing me to turn table legs, spindles for candle tables and even a four poster bed for my daughter.

However, I want to turn a skirt for a round top endtable. The skirt needs to be about 18-20" in diameter basicaly a ring, hollow in the middle and I am wondering if anyone has any plans or suggestions for how to rig up a motor and tool rest to turn such a thing?

I was thinking of gluing up a blank octagon mounting it to a sacrifical piece of plywood , then connecting to a motor shaft, and with a rigged tool rest and turning the skirt.

I have the idea , the motor, the pulleys to slow the turning down or speed it up, the turning tools, but that's it.

Failing this approach I have to do glue up's from thin pieces and bending, which has never really worked for me.

is this possible or a bad idea?

Any ideas /cautions /suggestions would be appreciated.

Mark

Re: Need a home made "outboard" Turning solution.

#2

Re: Need a home made "outboard" Turning solution.

fgvanatta

>Use a router and a cirle cutting jig.

Re: Need a home made "outboard" Turning solution.

#3

Re: Need a home made "outboard" Turning solution.

john lucas

>Don't know if you lathe has any outboard capabilities or not. I had lathe that had a simply knob on the outboard side. It was held on by a set screw. I made a wooden faceplate to fit it and glued a larger faceplate to that. I backed my drill press up to the lathe and rigged up a tool rest to the drill press table. This was my outboard tool rest. I turned a table top of somewhere around 16 to 20". I don't remember, that was a long time and many lathes ago.

A friend rigged up something similar with a motor clamped to his tool rest. I don't remember his tool rest exactly but it was some sort of plumber's nightmare that was bolted to the workbench and sat on the floor. I also don't remember how he slowed the motor down. I know it didn't run fast but don't remember any jack shafts or anything. Could have been a geared motor.

Re: Need a home made "outboard" Turning solution.

#4

Richard Allen

Re: Need a home made "outboard" Turning solution.

Richard Allen

>Turn the skirt on a fellow woodturners lathe which has enough swing to do this safely. As the diameter of the turning increases the hazards increase. This is NOT an opportunity to "shade tree" a solution, especially when there are lathes which can handle the task easily.

I would use 12 to 16 staves for the skirt. The plywood is a good idea. Mount that to a faceplate and turn it round and true. Make the stave 1/3 longer than you need.

I like to use epoxy for the glue with a filler. The attachment of the stave ring to the "plywood" involves a lot of epoxy and filler so that there is a good fillet between the staves and the plywood.

One clamp for each stave to be sure the stave is connected to the plywood

Two large hose clamps (you can connect smaller hose clamps together to make a larger hose clamp) to clamp the ring together.

Waxed paper is your friend.

Use a router with a 15 degree or 11 1/4 degree chamfer bit to establish the joint surfaces. Please note that the cut doesn't need to extend all the way to the outer edge as that will be the high points which will be turned away. Draw this on paper (1/4 scale or smaller) to see how this works.




Re: Need a home made "outboard" Turning solution.

#5

Re: Need a home made "outboard" Turning solution.

robert davis

>or a bandsaw with circle cutting jig.