Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

My band saw is wandering

Posts

My band saw is wandering

#1

My band saw is wandering

Duane Wiedman

>For years I've been able to use the standard rip fence and make pen and stopper blanks that are parallel. A few weeks ago the wood began to drift away from the fence. I thought maybe the blade was getting dull so I replaced it with a Timberwolf 1/2" 4 TPI (the same blade that was on it previously). This is on a Jet 14" (JWBS14CS) saw. While I was at it I replaced the tires, the cool blocks, made sure the wheels were Co-planar, oiled up the bearings and reset them. The blade teeth are centered in the top wheel(I also tried it with blade centered). As you suspect, the wood still drifts away from the fence. It even drifts when I use a sled to cross cut the stoppers. Can anyone guide me to what I missed or what I should revisit? Thanks for any help you can give.

Duane

Re: My band saw is wandering

#2

Re: My band saw is wandering

John K Jordan

>Could the tension be low? The stock springs sometimes weaken and the tension gauge becomes less than useful. My delta required using the 3/4" setting for 1/2" blades.

Also, did you set the fence for drift? Most saws need some adjustment. (Follow a straight line on a board freehand to determine the drift, stop halfway, set the fence to match the angle of the board.)

I've never run a bandsaw with the teeth in the center of the tire. Generally the teeth are more towards the front.

JKJ

Re: My band saw is wandering

#3

Don Pencil

Re: My band saw is wandering

Don Pencil

>Just a thought.

Check to see that the table is square to the blade.

Not so much the tilt degree, I'm thinking that the table may have pivited as it is a problem with both the fence and the sled.

Don

Re: My band saw is wandering

#4

Re: My band saw is wandering

Duane Wiedman

>Thank you guys. All good possibilities. I'll check them out. Thanks, Duane

Re: My band saw is wandering

#5

Re: My band saw is wandering

Grant Wilkinson

>In addition to all the other good suggestions, you can try moving the blade on the tires. The tires are likely crowned in the middle. If you put the blade toward the front of the tire, it is skewed toward the left of your saw when turning and will pull the wood that way. If you move the blade toward the back of the tire, it will be skewed toward the right of your saw and will pull the wood the other way. You can compensate for some of the pulling simply by moving the blade to one side or the other of the crown in the tire.

Re: My band saw is wandering

#6

Re: My band saw is wandering

Duane Wiedman

>I haven't tried the other suggestions yet but I'll put this one in the hopper also. Somethings bound to help.

Thanks,

Duane

Re: My band saw is wandering

#7

Re: My band saw is wandering

Tery Scott

>Hi Duane On my big band saw the same thing was happening

I had to revert to putting a line on the timber with a straight edge when I wanted to rip something and

cut by eye

I never release the tension as I forget that I have done so and turn on the saw and give myself a fright

After months of attempting to fix the problem I made the discovery that my blades had lost their set cutting mainly blanks the pressure is on the same side of the teeth . It appears that my blades (I have 10 so didn't try a new one ) were being sharpened but the saw doctor wasn't resetting them.

I have changed to bimetal blades that last 10 times longer

I had also had a big jamb up a year or so back and the top Guard was not square to the table so was applying a twisting action to the blade

Being a bit lazy i weren't bringing the guard down as close to the timber as I should have beenor checking that the clearance betweebn the bearings and blade was only the thickness of a piece of paper

Re: My band saw is wandering

#8

Re: My band saw is wandering

Duane Wiedman

>Thanks, Tery

That must have been a really scary jamb. Thanks for the additional suggestions. I hope to get to all of them today. If I do all of them a once then I won't know what really fixed the problem on the other hand I just want the problem fixed. Thanks all.

Duane

Re: My band saw is wandering

#9

Re: My band saw is wandering

Don Evans

>Hey Tery:

You being in NZ I'm wondering if you have flat wheels or crown on your BSaw?

You mentioned teeth pressing on wheel.

If you have flat wheels the teeth should not be hitting the wheel unless you are using blades that are less than 1/2". The wheel should be tilted so the teeth hang over the front edge, THIS IS FOR FLAT WHEELS ONLY.

FYI, I don't feel I really need to take the tension off mine due to fact that I've got a MiniMax 16, the MM16 not E16. This thing is build like a tank and it isn't gonna hurt the saw to leave tension up. However, because their are times where I'll go couple of weeks without turning it on, I do drop the tension. I took a 3 x 4" x 3/4" block of pine wood and put a card type magnet on back of it. On front I wrote, "Tension Blade before Turn ON" and put arrows showing which way to turn tensioning wheel.

I put this on the saw table in front of the blade when I detension it, and put it on front of top door when blade is tensioned.

Works for me anyway and I've not messed up since started using the sign.

Could also make one to go over the on/off switch may be better for some folks.

Don