Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

OT: Electric Motor

Posts

OT: Electric Motor

#1

OT: Electric Motor

TomCollins

>I bought a Grizzly dust collector at an auction and the motor has gone bad. I have a motor on order from Grizzly but it has been on back order since last July and my newest ship date is March 8. I have been trying to find a replacement motor on the net but not having much luck. It is an induction motor, 1 HP, 110/220 volt, 3450 rpm, totally enclosed fan cooled motor. The biggest problem I am having is that the shaft is 3/4" diameter and all the motors I am finding are 5/8" diameter.

Any of you motorheads out there have any suggestions on where I might find such a beast?

Thanks for any info

TomCollins

Re: OT: Electric Motor

#2

Re: OT: Electric Motor

Barry Irby

>Try WW Grainger.

I just spent a few minutes looking though their catalog. I am not much of a motor head. I did not see any motor meeting your specs, but they don't list the shaft sizes. At least i did not see it. I also didn't see induction motors listed, but that may be because I don't know one motor from another. I can't imagine that they don't list the shaft diameter. Clearly I am just not seeing it.

My thought would be to check on buying a motor with a 5/8" shaft and using a sleeve. OTOH, Grizzly may KNOW that the 3/4" shaft is necessary. Double check. Would not want to snap the shaft and have the impeller flying around.

Re: OT: Electric Motor

#3

Re: OT: Electric Motor

Ron Lynch

>Probably not going to be a lot of help, but if you have a frame number for your old motor it shouldn't be too difficult to cross reference different manufacturers for a suitable replacement. The frame number is used to identify a motor's physical characteristics, such as shaft diameter, keyseat size, height of shaft center above base line, mounting bolt size and location, etc. Find a motor with the same frame number and it will fit physically. Then you just have to match electrical specs.

Re: OT: Electric Motor

#4

Re: OT: Electric Motor

Galen Vetterick

>Ron's got the idea you need to look at the motor namplate and try and match the NEMA frame size. The older frame 66 motors had 3/4" shaft and not sure if many manufactures make anymore. We used a lot of frame 66 from Electra and Baldor and near the end they were special to get the 66 frame. We used aluminum end bell in our case. Think they now wind 184's for the application.

You may have to settle for a 56 frame and sleeve as suggested.

The motor is probably C face mounting and not foot mounted? C face is flange mounted at the end bell.

You might get a shop to rewind your existing motor if that is what is needed but many times it is cheaper to buy new.

Not even sure if Grizzley motors are NEMA motors.

A farm supply store or other machine shop dealing in motors may carry the sleeves to make a 56 frames work.

Re: OT: Electric Motor

#5

Don Pencil

Re: OT: Electric Motor

Don Pencil

>What is wrong with the motor?

Possibly try a motor repair shop. It may be repairable.

Don

Re: OT: Electric Motor

#6

Re: OT: Electric Motor

Dave Peebles Lyons, Ohio

>Hi Tom,

You might want to give Wyse Electric Motor repair a call.

They are in Archbold and have helped me out a couple of times.

419-445-5921

Good luck,

Dave

Re: OT: Electric Motor

#7

Re: OT: Electric Motor-More Info

TomCollins

>Dave P. I did take it over to Wyse. He didn't even want to look at it and told me it would cost as much for him to fix it as a new one costs.

Don P. It smelled like it was burning up and filled the basement with smoke.

I've attached a couple pictures. The main problem I am having is finding a motor with such an odd size shaft. It is 3/4 dia x 1-5/16" long. Where you see the green band on the shaft it steps up to 1"diameter.


Re: OT: Electric Motor

#8

Keith Tompkins

Re: OT: Electric Motor-More Info

Keith Tompkins

>another thought...change the pulley. new shaft diameter, same overall diameter. I found excellent pulleys online, just don't remember where.

Re: OT: Electric Motor

#9

Re: OT: Electric Motor-More Info

Jerry Whitaker

>Check the serial# on that baby..... #34....must be one of the first ones made. I assume they serialize them in orde.

Re: OT: Electric Motor

#10

Check the capacitor.

Doc Green

>Tom, pull off that half-cylinder cover plate that's up near the top and check the capacitor that you will find inside it. If it looks burned or charred, or if some nasty-looking chemical is oozing out of it, you will have found your problem. Replace the capacitor and the motor will be good as new.

~Doc

Re: OT: Electric Motor

#11

Re: OT: Electric Motor-More Info

Galen Vetterick

>Just because the sticker has 110 did you check to make sure someone had not changed to 220? What voltage did you connect to?

I am not surprised shop would not touch old non industry standard motor.

Suggestion to check capacitor on your own is fine if you are familiar with what you are doing.

The suggestion on just a different frame motor and adjusting for foot mounting changes and new pulley is good idea too.

Have purchase 1 Hp motors in larger frames like 143T and having 7/8" shaft turned to 3/4 but is expensive too.

Have to compare adapting some motor to overall cost you have in equipment and you be the judge.

I sure don't imagine drive system was engineered to have turned down shaft to have larger bearing for the overhung load or longer life!

Re: OT: Electric Motor

#12

Re: OT: Electric Motor-More Info

Guy Bratt

>After 34 years in the trade I can tell you, they only put so much smoke in a moter.

If you let it leak out... It will never work again.

Re: OT: Electric Motor

#13

Re: OT: Electric Motor-More Info

TomCollins

>Thank Goodness!!!! I am sick and tired of cleaning up puddles of smoke around that motor!

Still haven't found a good replacemet yet.

TomCollins