Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Epoxy Hazards

Posts

Epoxy Hazards

#1

Epoxy Hazards

David Belser

>I've been working with combining epoxy with my turnings. I'm using System 3 general purpose resin but my question about hazards applies to all epoxy systems. I got the "epoxy book" from System 3 and would strongly recommend it to anyone who wants to experiment with epoxy. The book has a good safety section that basically says repeated skin exposure will eventually lead to an allergic reaction that will make it impossible for one to work with epoxy. So I have been extremely careful to avoid skin contact always using gloves and disposable mix pots (plastic cups and plates, lots of paper towels)

The book states that because epoxy resins and hardener have high vapor pressures (don't evaporate much) the fumes are not a problem.

Very recently someone told me of a turner who lost there sense of smell from using epoxy! So I went and pulled up the MDS for the epoxies I'm using and found only a barely useful:

"Respiratory Protection: Normally none is required when adequate ventilation is provided."

I'm using what I would consider to be very small quantities at a time (~2 oz - half of a small cup) compared to what the boat builders that use this stuff must mix up and I'm doing this in a large room 20x25'.

I'm particularly interested because I'm exploring a process that requires working over/close to the epoxy as it gels for 2+ hours. I've had no issues doing this yet, but it may end up being a process that I do in front of an open window with a fan (unfortunately it is currently about 6 degrees outside!)

So my questions:

Has anybody had a problem with exposure (breathing) to epoxy fumes?

How much risk is there with this?

Have you lost your sense of smell permanently?

How much ventilation do you use when working epoxy?

- Dave

Re: Epoxy Hazards

#2

Re: Epoxy Hazards

john lucas

>I've used a lot of epoxy over the years. No problems at all so far. If I have to handle it I do use gloves but mostly because it's hard to get off your hands without using chemicals that will harm you. Never hurts to take precautions however.

Re: Epoxy Hazards

#3

Re: Epoxy Hazards

JB

>I had been using epoxy in re-constructing decomposing wood in old houses, taking all precautions to avoid skin contact but not concerned with respiration because all the work was outside or in well-ventilated areas.

Now I use a respirator because simply smelling the chemicals causes an immediate allergic reaction and my lungs become 'heavy'.

Wish I had ALWAYS been using a respirator

Re: Epoxy Hazards

#4

JL

Re: Epoxy Hazards

JL

>You can become sensitized by breathing epoxy fumes and develop problems, including rashes and allergic symptoms. A friend developed a nasty case of asthma which is triggered by epoxy fumes.

If you are going to be working in close quarters for long periods of time, I would suggest ventilation or a respirator.

Re: Epoxy Hazards

#5

Brad Vietje

Re: Epoxy Hazards

Brad Vietje

>Hi David,

System-3 epoxies may be formulated with non-toxic, or less-toxic compounds, but many epoxy resins and epoxides are known carcinogens.

I used to use a lot of highly toxic epoxies in relatively small quantities electron microscopy tissue preparation. I'm also informed that epoxies used in boat building (like West System) should be sanded with great care and adequate protection. They may have found newer resins that get around these issues, but a respirator is pretty cheap insurance. I've also heard of contact dermatitis, or skin sensitivity associated with epoxy use, but that might be different stuff than the West System. I've used West epoxy for building telescopes and rebuilding an old ice boat,and its absolutely fantastic stuff. BTW: the Gougean brothers are not only great boat building innovators, but well-known ice boaters, too.

My recollection -- to be verified -- is that one of the most dangerous parts of the whole shebang was the fine-textured thickener used to create the spreadable consistency we might be after... I could be wrong here, but I remember hat stuff being especially nasty, and since a sneeze could send half a can across the room, I'd be careful not to breathe the stuff until you feel sure of its toxicity.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Epoxy Hazards

#6

Better safe than.....

Dave Belser

>Clearly when your long term health is on the line it's better to err on the side of safe.

I'll call the System 3 folks tomorrow and see what their opinion is.

Most likely start using a positive ventilation set up that draws air away and blows it outside.

Re: Epoxy Hazards

#8

So True

Bill Howatt

>Now that I am older and have the benefit of a good dose of hindsight, I wish that I had taken more care with hazardous materials when I was younger. So far, I am lucky but I now realize that nobody, including myself, is invincible and nasty things certainly can catch up with you.

Bill

Re: Epoxy Hazards

#9

Jesper, Denmark

Re: Epoxy Hazards

Jesper, Denmark

>Brad, you are correct in that the colloidal silica is a serious breathing hazard. It is not the it is toxic as such, but its small particle size means that it may stay in your lungs for a long time - I am not sure if silicosis is the right term, but you get the idea.

A dust mask should take care of it - and do not stir it too vigorously till it has been wetted by the resin.

The epoxy itself should not produce too many fumes, as no solvents are involved and the vapor pressure of both components is very low. The dermatitis problem is probably mostly from the "hardener" component, as it is usually water soluble. It also gets spoiled over some time, as it absorbs moisture. The resin lasts a long time.

The term hardener is really wrong, as the epoxy is made up from two chemicals, which react together and combined form the epoxy resin.

Re: Epoxy Hazards

#10

Catalyst?

Jorge Casta�eda

>Hi Jesper,

Is catalyst a better word?

There is also a filler that is very finely cut cotton, which flies very easily too, yes respirator is a must.

Re: Epoxy Hazards

#11

Re: Catalyst?

David Belser

>Jorge - A catalyst is something that aids a chemical reaction but doesn't end up as part of the reaction. Epoxy part A and part B react and create the final "C" which is a different chemical than either A or B. The B part ends up in the result.

The catalyst in your catalytic converter doesn't get consumed it just speeds/assists the chemical reaction/change of the exhaust.

Re: Epoxy Hazards

#12

Re: Catalyst?

Jorge Casta�eda

>Thanks David,

Chemistry is one of my weaker points...

Re: Epoxy Hazards

#13

Re: Epoxy Hazards

Galen Vetterick

>David

We used epoxy and chopped glass roving to bed 36 and 42 inch bearings in the equipment we built. To thin the resin we used MEK (methyl ethyl ketone) so it would flow under the weight of the bearing. The chopped glass roving is light enough you can breath into your lungs (cancer causing). The MEK is a definite health risk!

Although mixed by weight the volume used at one time is about a gallon.

This has been done in our shop for over 40 years and they did this out on the main shop floor with no safety equipment!! Guess nobody complained or died immedately! I was in a seperate office 20 feet from the main shop and it gave me an instant headache from the smell that drifted in!

Our outsource fiberglass shops did use clothing and breathing equipment when spraying up but the people that rolled it only wore gloves and a simple dust mask.

About the same I would see on shop tours of RV manufactures that produced their own parts in past years.

I never had a problem with the small amounts I used for home and hobbies but then used no chopped glass or thinners either.

Retired now and only a few brain cells gone from this, I THINK!

Galen

Re: Epoxy Hazards

#14

The official response

David Belser

>I just got off the phone with tech support at System Three - lots of good information on what I'm doing, including using a vacuum and tinting.

For the two system 3 products I'm using - General purpose resin and Clear Coat, there is no need for any special ventilation or respiratory protection. Avoid skin contact or you may eventually develop a reaction.

Precautions should be taken when using additives (chemical thickeners) fillers (silica for instance) and also when sanding or heating the epoxy. Most of this is common sense.

The risks involved are *HIGHLY* dependent on the products you are using, "epoxy" is used to refer to a broad range of stuff, some of which is quite dangerous.

While it turned out to be a non-issue in my case, this is a good reminder to take health safety seriously. I hadn't even considered that might have been exposing myself in an extreme manner buy using this stuff in an unconventional way. If my friend hadn't mentioned anecdotal stories of health problems, I wouldn't have done the research.

MDS and tech support are your friends, use them!