Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Pierced frogs

Posts

Pierced frogs

#1

Pierced frogs

Mike Foster

>No, this isn't about a science project. This is my first try and test doing a pierced piece. I was really just experimenting, so did not really take a lot of time with any of the steps involved. I lightly cleaned up some fuzz with the radial bristles. I did not bother to remove burn/scorch marks inside the piercings. I used a woodburner to define some of the frogs. Then, just for fun, I tried a little coloring with prima colors. I didn't knock myself out (as apparent) with the coloring, was just seeing if coloring with markers would mix with the piercing. I also only pierced and colored what is shown in the picture, didn't bother with the other side. Probably won't finish the piece, but it gave me a real feel for what to expect.

I knew this piece was just practice as the base was far too thin in a couple of spots and the walls varied in thickness from 1/8 to 1/16. I decided to turn another piece yesterday and chucked up a chunk of maple. The shape I turned was a nice open form. All was proceeding well until I hit the rim with my light while it was spinning to use it for checking wall thickness. Instantly lost about 1 1/2" in height because the light chunked out a couple of pieces of the wall that had already been turned down to about 1/16. I went ahead and completed the form as it is just fine, albeit a little shorter.

I can't decide about the prisma colors, but may not do that again. It works ok on the outside, but getting color into the holes is next to impossible. Airbrush probably works better. I'll have to decide about the filing/sanding on the inside of the holes. Seems like way too much work, but almost needed to make a clean look. Thanks for all the advice and help. I expect I'll try a real piece in the future.

This is also a test for uploading a photo for me.


Re: Pierced frogs

#2

Re: Pierced frogs

john lucas

>Mike That has a lot of potential. It well worth working out the details. As far as your statement about going further being too much work. That you have to decide for yourself. I'm in the same boat believe me. When I look at the work at the instant gallery in the AAW symposium I realize pretty quickly that the work where they did spend the time really stands out. So I ask my self am I just making this for fun and to show friends, or am I making this piece to be a truely nice piece worthy of praise from the higher ups. If so then you have to throw away the time element and just build it. In the long run even you will forget how long it takes. I never get my money out of these pieces. At least not so far. However I don't regret doing them.

Re: Pierced frogs

#3

Re: Pierced frogs

Don at Central Illinois

>I agree, I really like the concept. The frogs fit together very well. As John, said, it depends on why you are doing this. I don't think I have the patience for all of the piercing, sanding etc. But I sure admire what other do. Keep it up and show us the final product.

Re: Pierced frogs

#4

Re: When I saw that title I was ....

JamieDonaldson

>... a bit hesitant to open the file, but I trusted Mike to not gross us out with a skewered Kermit! It is a lot of work Mike, and to be done well it has to be done right- whatever your tolerance for pain!

Re: Pierced frogs

#5

Re: Pierced frogs

AndiWolfe

>Most surface enhancements take a lot of time and patience as you've now found out by personal experience. If you do continue with this work, I'll give you a few hints:

1) start with a thin wall - you'll spend less time on the piercing.

2) finish the surface to a high grit of sand paper if you're going to use penetrating dyes of any sort, including the prisma color markers. You'll need to clean up the frayed edges of the piercing before applying any color.

3) prismacolor markers can be applied with an artist paintbrush - I prefer nylon bristles. You should be able to reach inside the pierced wall with a brush tip.

4) never apply prismacolor markers directly from the felt tip - you'll not be able to work out the coloring to an even consistency and blending will be very blotchy.

5) 91% rubbing alcohol works well for blending prismacolor markers.

Re: Pierced frogs

#6

Thanks Andi

Mike Foster

>I really appreciate the your advice. I have played with colors using acrylics, dyes and airbrushing, but have only used prisma colors on one piece. I sat in on one of your demos, and remembered that you use alcohol to help blend them, but I got the technique wrong. I used the felt tips and tried dipping them into DNA. Found that this did not really blend the colors and wound up with the blotchiness you mentioned. Makes sense that picking the color up with a brush would make for better blending. I will get some rubbing alcohol and play with the prisma colors some more. Do you pick up the color off of the felt tip with the brushes?

I guess I'll just have to put in the time to get a nice result. I have turned a new piece that is ready to pierce which is thinner and more consistent walls (about 1-1.5 mm). It may be a while, but if it comes out I'll post it when done.

Re: Pierced frogs

#7

Re: Thanks Andi

AndiWolfe

>Yes, pick up the color off the felt with the brush. Have a great time playing with new techniques - always an adventure.