Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Questions for piercers

Posts

Questions for piercers

#1

Questions for piercers

Mike Foster

>I have had an open form sitting around in the shop for a while that I turned after purchasing a Munro Hollower (love the tool). I turned this vessel fairly thin, just to test the hollower. I realized the walls got real thin at the base but finished turning it anyway and stuck it on the shelf with other pieces that didn't quite make it. I decided to give a go at piercing tonight since I had all the rig to do it (byproduct of my other life). It didn't take long to realize that , though the piece I was working on was fairly thin (1/8") this may be a bit more than what other pierced pieces are. Piercing is not impossible, just slow. Further down the vessel where it thinned out to about 1/16" piercing went much faster.

So, to all those with experience piercing.

How thin do you aim for walls?

How do you clean up the piercings once done (needle files?).

Do you bother to remove the burn marks left by the bur, or is this why so many pierced pieces are air brushed?

I'll post a pic of my practice piece after it is a little further on. I want to try a couple more things with it for fun.

TIA

Mike

Re: Questions for piercers

#2

Re: Questions for piercers

john lucas

>Mike I've only done a little piercing. Mostly because I don't have the Hight speed tools and doing this with a Dremel is incredibly slow and difficult because the tool wants to follow the grian. With a High speed tool (400,000 rpm) and a really thin piece of wood it's almost like writing. It is much easier to control.

I took a class with Binh Pho and go to use the High speed air carvers. I realized pretty quickly just what you found out. The thinner the better. One of the pieces I made was a goblet. The walls were about 1/16 and pierced very easily and controllably. The bottom was on the fat side of 1/8" and was extremely slow and control was harder.

As far as cleaning up the piercing. With the High speed tools I don't think most people do other than light sanding on the inside and outside. Hope some of them respond because I would like to know also. Binh doesn't but then many of his pieces are airbrushed afterwords. As you know the HSS piercing tools burn the edges so there isn't much to clean up, however the edges of the holes are black.

Using the Dremel The edges of the holes are wood colored but there is a fuzz left that needs to be cleaned. I use and rat tail file and some diamond carving files to clean up the fuzz. The plus side of the Dremel is that it has more horsepower and will cut through much thicker wood. It just takes more patience than most people have and since it tries to grab the wood it's terribly easy to cut where you don't want to.

Re: Questions for piercers

#3

Re: Questions for piercers

Donna Banfield

>Mike, you can clean up the fuzz that's left with the 3M radial bristle discs. They come in grits from 80 - 400, and do an excellant job without damaging the piercing/carving. They are not cheap, though, and last no longer than good quality sandpaper does.

Re: Questions for piercers

#4

Re: Questions for piercers

Mike Foster

>Thanks Donna. I have some of them and will give them a try. Do you bother trying to rid the burn/scorch of the insides of the piercings?

Re: Questions for piercers

#5

Re: Questions for Donna

Carole Valentine

>Donna, have you ever had a problem with the blue disks leaving color on the wood? I have and I quit using them on light colored woods for that reason. Maybe mine came from a bad batch.

Re: Questions for piercers

#6

Re: Questions for piercers

Hal Taylor

>Mike, sounds like you are using a high speed drill. As you have found out 1/8 is slower than 1/16 which makes sense, but quite doable. So, you have seen about where you should be as for thickness. The thinner the better is not good, however. Too thin becomes brittle and breaks easily.

As for the charred, black edges - depends on what you want the product to look like. Even with airbrushing some of the black may show. And if you want your product to look like Malcolm Zander's pieces, a lot (and I mean a lot) of "sanding" with diamond files is necessary.

Re: Questions for piercers

#7

Re: Questions for piercers

Mike Foster

>Thanks Hal,

I don't know if work like Malcolm's is in the cards for me. I have a lot of patience, but maybe not that much. I turned another piece today and got it to a pretty consistent 1/16". I don't have a design for the piercing yet, but am working on it. I also did some more piercing on my practice piece. I don't intend to do much clean up and certainly no filing in the holes. I don't know that it will ever get finished, but I am experimenting with color and burning with it. Will post a pic after that.

Re: Questions for piercers

#8

Re: Questions for piercers

Donna Banfield

>So far, Mike, my piercings have been protoypes, or experiments. Some woods burn or scorch more than others, and for those I enhanced the burn with a woodburning tip. I'm not exactly thrilled with the result of that, however. A few people who have seen it thought it looked cool, but I don't.

Airbrushing is something I plan to try, and I would be using acrylic paints, so I suppose that the paints would conceal the burned edges better.

Re: Questions for piercers

#9

Re: Questions for Donna

Donna Banfield

>Carol, I've never had any color transfer from the radial bristle discs yet. The woods I've used them on have been maple, yew and black walnut. I never noticed any color transfer on the maple or yew.

It could be just a fluke thing; never heard of it before, but now that I'm aware, I'll be looking much closer now.