Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Saved a few $$$

Posts

Saved a few $$$

#1

Steven Antonucci

Saved a few $$$

steve antonucci

>I wanted to make a longer tool rest for my lathe and I originally thought I would get the steel and have someone weld it for me. I was talking to my fried Wil who said that one of the local scrap tards would probably have 1" round stock, so I set off on the adventure this past Saturday.

Then, as if struck by lightning, I remembered something. I have one of those tool rest systems with a 4" round tool rest. I probably paid $15 for it. It has a little spacer that converts it to accept the round bar. SO, all I needed was the round bar!

Drove to their office, and we found a round that fit the bill within 5 minutes. It was badly rusted, and 3x as long as I needed, but it only cost $2. I drove to Wil's house to show him my conquest (and borrow his 1/2"x13 tap) and he said "ahh, we can just do it here...won't take very long!) A couple of minutes later, I had my threaded hole.

I drove home, and quickly tested it out. It fit perfectly. After about 10 minutes with some medium steel wool, some WD-40 and a file, tt was clean enough to be a tool rest. I noticed it has some yellow paint that clearly looks to me to be school bus yellow, so I suspect that this bar was a bus part in it's prior life. I blued the steel with some Birchwood Casey, and called it a day.

My only remaining decision is how long do I want to leave it on the right side before I cut it? The reason I made this rest is to cut into deep open vessels without the enormous overhang. I'm thinking maybe 12"- 15" max, and then making another one out of the other half...

Not a bad ROI if you ask me...


img

Re: Saved a few $$$

#3

What do you mean by scrap tards?

Dave Peebles Lyons, Ohio!

>Happy to hear this worked for you Steve, but I am confused by this.?

Dave

Re: Saved a few $$$

#4

Re: What do you mean by scrap tards?

Don Orr

>Nice job Steve.

Dave-maybe he meant yards. T is next to Y on the keyboard. I do that all the time ;-))

Re: Saved a few $$$

#5

Steven Antonucci

New Tards cost too much :-)

steve antonucci

>Plus they are very hard to find. (T is next to the Y isn't it? :-)

The main point of my post was the ridiculous costs of the item at Woodcraft (which I generally like). I wanted to point out that I could probably make 3 of these for the $2 I spent. I suspect that they started at $2, added some cost for machining, and then all of the markups to have profit margin to end up at $35. If you order it online, you can tack on shipping, which I assume they also have some margins built in.

An educated consumer knows where his money is going. Buy wisely, and save your $$$ for things you can't make...

S

Re: Saved a few $$$

#6

Re: Saved a few $$$

Jorge Castaneda~Downeast Maine

>Steve,

Good job, 11" 0r 12" will be tops, after that it will vibrate, tunning fork kind of thing, unless you figure a way to stiffen it, make the short arm about 3", if it gets on the way you can always shorten it, mine is 2 1/4" and most of the time wishh it was a little longer.

You could make a curved tool rest with the reminder, a friend thinks curved rests are stiffer...

Let us know how you fare

Jorge

Re: Saved a few $$$

#7

Re:Labor costs :-)

adrien

>Steve, I figure the time you spent doing this must have been about three or four hours. If your time is worth $10 an hour, then the $40 to Woodcraft ain't that expensive......

Re: Saved a few $$$

#8

ebd

Re: Saved a few $$$

ebd

>Absolutely right. A while back I bought the rest in the picture below. Since then I've made numerous specialty rests from scrap flat and angle iron stock. So much cheaper and you can get exactly the size and shape and curve that you need which is most often not the case with what is commercially available rests. This guy is even easier because it requires no threading just a little countersink at the point where the set screw hits. It's not as sturdy as yours so it wouldn't be appropriate for deep hollowforms, but I don't do those. I still use my standard rests for most stuff but when I need something special I can make exactly what I need myself from what I've got on hand for free, with no shipping, and no wait.


img

Re: Saved a few $$$

#9

:)

Dave Peebles Lyons, Ohio!

>

Re: Saved a few $$$

#10

Steven Antonucci

I was out anyway

steve antonucci

>So I don't count the time driving there, since it was across the street from Home Depot anyhow. And Campbell Small Engine (my Chainsaw shop). Had no real time to invest.

Then, I had to pass by Wil's house on the way home, so it only added 5 minutes to my trip home.

I will say that it did take me 20 minutes in Wil's shop, and another 15 in mine. Call it 40 minutes total.

$35/40 minutes is closer to $55/hr. seems like a deal to me.

S