Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

1642 NEEDS TO BE ABLE TO MOVE

Posts

1642 NEEDS TO BE ABLE TO MOVE

#1

1642 NEEDS TO BE ABLE TO MOVE

Dennis Taylor

>I have a Jet-1642, that currently sits on 4x4 posts, and the lathe is lagged to them, and they work fine, but I need to be able to move the lathe around the shop/garage. I went to local WC and they have a 3" wheel with a 3/8" stem that would fit into the leveler holes in the legs, and the wheels are rate at 275lbs each, and they told me that they have several of them they put on casters for people. Any use this to allow shop mobility?...I have read a lot of discussed about a lift table from HF, but it is around 275.00, and that is a little high right now. Any input is appreciated and enjoy the day. Dennis

Re: 1642 NEEDS TO BE ABLE TO MOVE

#2

Katherine Kowalski

Re: 1642 NEEDS TO BE ABLE TO MOVE

Katherine Kowalski

>Hi Dennis,

I looked into buying some casters for my large Woodfast recently. (Ended up finding a better place for the lathe so I didn't have to move it, thus I didn't make a purchase.) However, one product at WoodCraft that caught my attention was a set of 3" casters that had little rubber feet that came down, allowing you to stabilize the lathe when in use. Seemed like a good option, especially for reducing vibration/movement of the machine.

Katherine

Re: 1642 NEEDS TO BE ABLE TO MOVE

#3

Re: 1642 NEEDS TO BE ABLE TO MOVE

ray-t

>Mount an axel on the heavy end of the lath,put some handles on the other end . When you lift the handles,the lathe mount clears the floor.Then you have a wheelbarrow type setup. Works for me, cheaper also . Ray-t

Re: 1642 NEEDS TO BE ABLE TO MOVE

#4

Re: 1642 NEEDS TO BE ABLE TO MOVE

Marc Phillips

>I wouldn't want my lathe raised up 3"... would make it real uncomfortable for me. If you are very tall it might be ok.

I had another lathe with the wheelbarrow setup Ray described.. worked well and there was no added vibration that I could tell.

Re: 1642 NEEDS TO BE ABLE TO MOVE

#5

Vega machine movers *LINK*

john lucas

>I don't have one of these on my wood lathe but do have one on my Bandsaw. I did have one under my Nova 3000. They work great. You can build up a wooden base if you need the lathe higher.


http://www.vegawoodworking.com/

Re: 1642 NEEDS TO BE ABLE TO MOVE

#6

Re: 1642 NEEDS TO BE ABLE TO MOVE

Mike Jones, in Redding, Ca

>If you do not have to move often, like each day, a floor jack (the kind of hydraulic jack with four wheels)makes a move safely. The lathe need only to be raised a bit. Move one end at a time.

Re: 1642 NEEDS TO BE ABLE TO MOVE

#8

Re: Vega machine movers

Dennis Taylor

>John,

does the mover allow 1 person to move around shop? I read the web info and sounds like it lifts the lathe about an 1 1/2 off the floor so that should help with the uneveness of a garage floor. can you steer the unit, meaning does it steer like casters or is it straight in and out?...thanks...Dennis

Re: 1642 NEEDS TO BE ABLE TO MOVE

#9

Re: 1642 NEEDS TO BE ABLE TO MOVE

Dennis Taylor

>would need to move each day, from the center of the garage to an adjacent wall out of the way. So it needs to be something stable. I was going to try and use casters, but not sure if the casters from woodcraft item 148595 would do the trick or not. the store rep, said he has put several large lathes on these 3" 3/8 stem casters and they worked fine with out any issue. I turn the largest item is a platter, and mostly smaller items, so maybe that will help with info. tks..Dennis

Re: 1642 NEEDS TO BE ABLE TO MOVE

#10

vega mover

Grant Wilkinson

>Dennis

I have the mover from Vega under my Vega bowl lathe. I can move the lathe easily around my shop. It steers with no problem. The mover comes with a handle that has two wheels on the end of it. When you use it to lift one end of the mover you have those two wheels and the two on the bottom of the mover itself on the floor.