Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Nova 3000 help needed

Posts

Nova 3000 help needed

#1

Nova 3000 help needed

Jim Canning

>I have two lathes, a PM 3525 and a Nova 3000. Because it is so cold in my shop/garage I move the nova inside the basement to turn on it

during the winter,the PM is just way to heavy to be moving it around.

My problem is that if I take anything stronger then a very light cut the motor starts to come to a stop.I have the belt on the highest speed and will turn it up as fast as I can and it still wants to stop. I have tried every setting and still the same results.

Is it the belt or is the motor getting ready to die? Does anyone have any suggestions?

Thank you in advance.

Jim

Re: Nova 3000 help needed

#2

Steven Antonucci

Never had the issue-

steve antonucci

>only a few simple ideas. Assuming that you look at the belt and nothing obvious jumps at you, double check that the slack is out and the belt is properly tensioned.

If that looks like the case, remove the belt and CAREFULLY try to stall the motor by grabbing the pulley. If it slows at all, the motor is probably bad. I WOULD ONLY DO THIS STANDING BEHIND THE LATHE WITH MY HAND ON TOP OF THE PULLEY. (Just in case your motor is fine...)

S

Re: Nova 3000 help needed

#3

Re: Never had the issue-

John Lucas

>Use a stick to rub against the pulley on the motor. This is a safe way to see if you can stall it. If you have the smallest pulley on the motor and the biggest on the lathe spindle you should not be able to stall it unless you take a very large cut on a big piece.

Re: Nova 3000 help needed

#4

Re: Nova 3000 help needed

Jorge Castaneda~Downeast Maine

>Jim,

We have something in common, we own the same lathes and my Powermatic is also in an unheated shed... Have you tried in the low speeds? those give you more power, the high speeds is a trade off, unless you have a very heavy piece that will act as a flywheel.

I did have a lot of trouble when I first got the nova, it went away when I finally got the motor pulley perfectly aligned with the one on the headstock.

Your may be a different cause, but look into that anyway.

Good luck

Jorge

Re: Nova 3000 help needed

#5

Re: Nova 3000 help needed

Carole Valentine

>I'm having a similar problem with my DVR (no belts there). Any piece of wet, slightly out of balance wood 10" or larger and I just can't rough it out...even with light cuts. The thing stalls and gives me the low rpm message. It will stall with just the wood turning and me not even touching it. Never used to have the problem and I have roughed 15" pieces on it. Didn't think about the motor...I sure hope not. Once I get a piece so I can run above 500 rpm, things seem to go OK. Smaller light pieces are fine.

Re: Nova 3000 help needed

#6

Re: Nova 3000 help needed

Tery Scott

>How far away is the power supply ,Voltage drop under load can cause your problem or if The lead is to small or two long

Cheers

Re: Nova 3000 help needed

#7

Re: Nova 3000 help needed

Barry Irby

>Carole, Surely you have contacted Tom Geist, Their "local" Rep? Local being West Virginia. I don't have his number but I am sure you can find it or some kind better organized soul will tell you.

Re: Nova 3000 help needed

#8

Re: Nova 3000 help needed

Carole Valentine

>Yes I have, but the problem seems to be intermittent. When he called me back the lathe was doing fine. :(

Re: Nova 3000 help needed

#9

Re: Nova 3000 help needed

Carole Valentine

>Don't know about Jim, but my supply is less than 3 feet from the lathe.

Re: Nova 3000 help needed

#10

Dick Hines

Re: Nova 3000 help needed

Dick Hines

>I was at the NC symposium in Oct and one of the demo rooms I was in had a Nova DVR as the demo lathe. I noticed that when it was put under a heavy load, taking heavy cuts, that it would loose a lot of RPM's. Is this common to the Nova lathes?